參數資料
型號: INTEL82802AB
廠商: Intel Corp.
英文描述: Firmware Hub (FWH)
中文描述: 固件集線器(固件樞紐)
文件頁數: 15/53頁
文件大?。?/td> 471K
代理商: INTEL82802AB
Intel
82802AB/AC Firmware Hub
R
Datasheet
15
Interface
Symbol
Type
Intel
FWH
A/A Mux
Name and Function
ID[3:0]
I
X
Identification Inputs.
These four pins are part of the mechanism
that allows multiple parts to be attached to the same bus. The
strapping of these pins is used to identify the component. The boot
device must have ID[3:0] = 0000, and it is recommended that all
subsequent devices use sequential up-count strapping (
0001,
0010,0011,...
). These pins are pulled down with internal resistors, with
values between 20 and 100 k
, when in the Intel FWH mode. Any
ID pins pulled high will exhibit a leakage current of approximately
200
μ
A. Any pins intended to be low may be left to float. In a single
Intel FWH system, all may be left floating.
A/A Mux = A[3:0]
FGPI[4:0]
I
X
Intel FWH General Purpose Inputs.
These individual inputs can be
used for additional board flexibility. The state of these pins can be
read immediately at boot, through Intel FWH registers. These inputs
should be at their desired state before the start of the PCI clock
cycle during which the read is attempted, and they should remain at
the same level until the end of the read cycle. They may
only
be
used for
3.3-V
signals. Unused FGPI pins must
not
be floated.
A/A Mux = A[10:6]
TBL#
I
X
Top Block Lock.
When low, it prevents programming or block erase
to the highest addressable block (7 in a 4-Mbit, 15 in an 8-Mbit
component), regardless of the state of the lock register. TBL#-high
disables hardware write protection for the top block, though register-
based protection still applies. The status of TBL# does not affect the
status of block-locking registers.
A/A Mux = A4
WP#
I
X
Write Protect.
When low, prevents programming or block erase to
all but the highest addressable block (0-6 in a 4-Mbit, 0-14 in an 8-
Mbit component), regardless of the state of the corresponding lock
registers. WP#-high disables hardware write protection for these
blocks, though register-based protection still applies. The status of
TBL# does not affect the status of block-locking registers.
A/A Mux = A5
A[0:10]
I
X
Low-Order Address Inputs.
Inputs for low-order addresses during
read and write operations. Addresses are internally latched during a
write cycle. For the A/A Mux interface, these addresses are latched
by R/C# and share the same pins as the high-order address inputs.
DQ[0:7]
I/O
X
Data Input/Outputs.
These pins receive data and commands during
CUI write cycles and transmit data during memory array, status
register, and identifier code read cycles. Data pins float to high
impedance when outputs are disabled. Data is internally latched
during a write cycle.
OE#
I
X
Output Enable.
Gates the device’s outputs during a read cycle
R/C#
I
X
Row-Column Address Select.
For the A/A Mux interface, this pin
determines whether the address pins are pointing to the row
addresses (A[0:10]) or the column addresses (A[11:19]).
WE#
I
X
Write Enable.
Controls writes to the CUI and array blocks.
Addresses and data are latched on the rising edge of the WE#
pulse.
相關PDF資料
PDF描述
INTELDX2 High-Performance 32-Bit Embedded Processor(高性能32位嵌入式處理器)
INTELDX4 Embedded Write-Back Enhanced Processor(32位回復嵌入式增強型處理器)
IPS54511 FULLY PROTECTED HIGH SIDE POWER MOSFET SWITCH
IPS5451 FULLY PROTECTED HIGH SIDE POWER MOSFET SWITCH
IPS5451S FULLY PROTECTED HIGH SIDE POWER MOSFET SWITCH
相關代理商/技術參數
參數描述
INTELLIGENT CHARGER + 4AA 制造商:Energizer 功能描述:Bulk
INTELLI-INCH-LR-STARTER K 制造商:ALL MOTION 功能描述:Intelli-Inch Stepper & Controller Starter Kit
INTELLIPANEL 制造商:GJD 功能描述:EXTENSION LEAD 8GANG INTELLIPANEL 制造商:GJD 功能描述:EXTENSION LEAD, 8GANG, INTELLIPANEL
INTELLIPLUG 制造商:GLOBAL COMMUNICATIONS 功能描述:ADAPTOR 3WAY INTELLIPLUG
INTELLIPROBE 100 制造商:Fluke Networks 功能描述:TONE + PROBE KIT