參數資料
型號： IDTTSE2002B3CNRG
廠商： IDT, Integrated Device Technology Inc
文件頁數： 29/30頁
文件大?。?/td> 423K
描述： IC TEMP SENS EEPROM DFN-8
標準包裝： 120
功能： 溫度監控系統（傳感器）
傳感器類型： 內部
感應溫度： -20°C ~ 125°C
精確度： ±1°C（最小值）
拓?fù)洌?/td> ADC（三角積分型），控制邏輯，寄存器庫
輸出類型： 2 線串行，I²C?/SMBUS?
輸出警報： 無
輸出風扇： 無
電源電壓： 3 V ~ 3.6 V
工作溫度： -20°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 8-VFDFN 裸露焊盤
供應商設備封裝： 8-VFQFPN（2x3）
包裝： 管件
29 of 30
May 12, 2010
 
IDT Confidential
Use in a Memory Module
In the Dual Inline Memory Module (DIMM) application, the TSE2002B3C is soldered directly onto the printed circuit module. The three Select
Address inputs (SA0, SA1, SA2) must be connected to V
SSSPD
 or V
DDSPD
directly (that is without using a pull-up or pull-down resistor) through the
DIMM socket (as shown in the Unique Addressing table). The pull-up resistors needed for normal behavior of the I
2
C bus are connected on the I
2
C
bus of the mother-board
Unique Addressing of SPDs in DIMM Applications
Note: 0 = V
SSSPD
, 1 = V
DDSPD
.
The Event pin is expected to be used in a wire-OR configuration with a pull-up resistor to VDDSPD on the motherboard. In this configuration,
EVENT should be programmed for the active low mode. Also note that comparator mode or TCRIT-only mode for EVENT on a wire-OR bus will show
the combined results of all devices wired to the EVENT signal.
Programming the TSE2002B3C
The situations in which the TSE2002B3C is programmed can be considered under two headings:
"   When the DIMM is isolated (not inserted on the PCB motherboard)
"   When the DIMM is inserted on the PCB motherboard
DIMM Isolated
With specific programming equipment, it is possible to define the TSE2002B3C content, using Byte and Page Write instructions, and its
write-protection using the SWP and CWP instructions. To issue the SWP and CWP instructions, the DIMM must be inserted in the application-specific
slot where the SA0 signal can be driven to VHV during the whole instruction. This programming step is mainly intended for use by DIMM makers,
whose end application manufacturers will want to clear this write-protection with the CWP on their own specific programming equipment, to modify the
lower 128 Bytes, and finally to set permanently the write-protection with the PSWP instruction.
DIMM Inserted in the Application Mother Board
As the final application cannot drive the SA0 pin to V
HV
, the only possible action is to freeze the write-protection with the PSWP instruction. Refer
to the Acknowledge When Writing Data or Defining Write Protection table on how the Ack bits can be used to identify the write-protection status.
DIMM Position
SA2
SA1
SA0
0
0
0
0
1
0
0
1
2
0
1
0
3
0
1
1
4
1
0
0
5
1
0
1
6
1
1
0
7
1
1
1
相關PDF資料
PDF描述
IPM6220ACAZ-T IC REG 5OUT BUCK/LDO SYNC 24SSOP
IR2170 IC CURRENT SENSE 600V 1MA 8-DIP
IR2171STR IC CURRENT SENSE 8SOIC
IR2172S IC CURRENT SENSE 8SOIC
IR2175STR IC CURRENT SENSE 0.5% 8SOIC
相關代理商/技術參數
參數描述
IDTTSE2002B3CNRG8 功能描述:IC TEMP SENS EEPROM DFN-8 RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:3,000 系列:- 功能:溫度開關 傳感器類型:內部 感應溫度:85°C 分界點 精確度:±6°C（最小值） 拓?fù)?ADC（三角積分型），比較器，寄存器庫 輸出類型:開路漏極 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) 其它名稱:ADT6501SRJZP085RL7-ND
IDTTSE2002GB2A1NCG 制造商:Integrated Device Technology Inc 功能描述:IC TEMP SENS EEPROM DFN-8
IDTTSE2002GB2A1NCG8 制造商:Integrated Device Technology Inc 功能描述:IC TEMP SENS EEPROM DFN-8
IDTTSE2002GB2A1NRG 制造商:Integrated Device Technology Inc 功能描述:IC TEMP SENS EEPROM DFN-8
IDTTSE2002GB2A1NRG8 制造商:Integrated Device Technology Inc 功能描述:IC TEMP SENS EEPROM DFN-8
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*