參數資料
型號: IDT821054PQF
廠商: IDT, Integrated Device Technology Inc
文件頁數: 5/45頁
文件大?。?/td> 0K
描述: IC PCM CODEC QUAD MPI 64-PQFP
標準包裝: 84
類型: PCM 編解碼器/濾波器
數據接口: PCM 音頻接口
ADC / DAC 數量: 4 / 4
三角積分調變:
電壓 - 電源,模擬: 4.75 V ~ 5.25 V
電壓 - 電源,數字: 4.75 V ~ 5.25 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 64-QFP
供應商設備封裝: 64-PQFP(14x14)
包裝: 管件
其它名稱: 821054PQF
13
IDT821054 QUAD PROGRAMMABLE PCM CODEC WITH MPI INTERFACE
INDUSTRIAL TEMPERATURE RANGE
channels’ SI1 and SI2 status changes can be cleared by applying a read
operation to GREG9. If SB1, SB2 and SB3 pins are configured as
inputs, a read operation to GREG10, GREG11 and GREG12 clears the
interrupt generated by the corresponding SB port of all four channels. A
read operation to LREG4 clears all 7 interrupt sources of the specified
channel.
2.6
DEBOUNCE FILTERS
For each channel, the IDT821054 provides two debounce filter
circuits: Debounced Switch Hook (DSH) Filter for the SI1 signal and
Ground Key (GK) Filter for the SI2 signal. See Figure - 5 for details. The
two debounce filters are used to buffer the input signals on SI1 and SI2
pins before changing the state of the SLIC Debounced Input SI1/SI2
Register (GREG9). The Frame Sync (FS) signal is necessary for both
DSH and GK filters.
The DSH[3:0] bits in LREG3 are used to program the debounce
period of the SI1 input of the corresponding channel. The DSH filter is
initially clocked at half of the frame sync rate (250 s). Any data
changing at this sample rate resets a counter that clocks at the rate of 2
ms. The value of the counter is programmable from 0 to 30 via LREG3.
The debounced SI1 signals of Channel 4 to 1 are written to the SIA[3:0]
bits in GREG9. The corresponding SIA bit will not be updated until the
value of the counter is reached. The SI1 pin usually contains the SLIC
switch hook status.
The GK[3:0] bits in LREG3 are used to program the debounce
interval of the SI2 input of the corresponding channel. The debounced
SI2 signals of Channel 4 to 1 are written to the SIB[3:0] bits in GREG9.
The GK debounce filter consists of a six-state up/down counter that
ranges between 0 and 6. This counter is clocked by the GK timer at the
sampling period of 0-30 ms, which is programmed via LREG3. If the
sampled value is low, the value of the counter will be decremented by
each clock pulse. If the sampled value is high, the value of the counter is
incremented by each clock pulse. When the value increases to 6, it sets
a latch whose output is routed to the corresponding SIB bit. If the value
decreases to 0, the latch will be cleared and the output bit will be set to
0. In other cases, the latch and the SIB status remain in their previous
state without being changed. In this way, at least six consecutive GK
clocks with the debounce input remaining at the same state can effect
an output change.
Figure - 5 Debounce Filter
2.7
CHOPPER CLOCK
The IDT821054 provides two programmable chopper clock outputs
CHCLK1 and CHCLK2. They can be used to drive the power supply
switching regulators on SLICs. The two chopper clocks are synchronous
to MCLK. The CHCLK1 outputs a signal which clock cycle is
programmable from 2 to 28 ms. The CHCLK2 outputs a signal which
frequency can be 256 kHz, 512 kHz or 16.384 MHz. The frequencies of
the two chopper clocks are programmed by global register GREG5.
2.8
DUAL TONE AND RING GENERATION
The IDT821054 provides two tone generators (tone generator 0 and
tone generator 1) for each channel. They can produce signals such as
test tone, DTMF, dial tone, busy tone, congestion tone and Caller-ID
Alerting Tone, and output it to the VOUT pin.
The dual tone generators of each channel can be enabled by setting
the TEN0 and TEN1 bits in LREG10 to ‘1’respectively.
The frequency and amplitude of the tone signal are programmed by
the Coe-RAM. The frequency and amplitude coefficients are calculated
by the following formulas:
Frequency coefficient = 32767
cos(f / 8000 2 π)
Amplitude coefficient = A
32767 sin(f / 8000 2 π)
Herein, 'f' is the desired frequency of the tone signal, 'A' is the scaling
parameter of the amplitude. The range of 'A' is from 0 to 1.
A = 1, corresponds to the maximum amplitude of 1.57 V.
A = 0, corresponds to the minimum amplitude of 0 V.
It is a linear relationship between 'A' and the amplitude. That is, if
A=
β ( 0<β<1), the amplitude will be 1.57 β (V).
The frequency range is from 25 Hz to 3400 Hz. The frequency
tolerances are as the following:
25 Hz < f < 40 Hz, tolerance <
±12%
DQ
E
DQ
DSH[3:0]
Debounce
Period
(0-30 ms)
DQ
GK[3:0]
Debounce
Interval
(0-30 ms)
up/
down
Q
6 states
Up/down
Counter
7 bit Debounce
Counter
7 bit Debounce
Counter
= 0
≠ 0
GK
SIB
SIA
SI1
4 kHz
SI2
RST
FS/2
相關PDF資料
PDF描述
IDT82V3001APVG8 IC PLL WAN W/SGL REF INP 56-SSOP
IDT82V3010PVG IC PLL WAN 51/E1/OC3 DUAL 56SSOP
IDT82V3011PVG IC PLL WAN T1/E1/OC3 SGL 56-SSOP
IDT82V3012PVG8 IC PLL WAN T1/E1/OC3 DUAL 56SSOP
IDT82V3155PVG IC PLL WAN T1/E1/OC3 DUAL 56SSOP
相關代理商/技術參數
參數描述
IDT821054PQFG 功能描述:IC PCM CODEC QUAD MPI 64-PQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 編解碼器 系列:- 標準包裝:2,500 系列:- 類型:立體聲音頻 數據接口:串行 分辨率(位):18 b ADC / DAC 數量:2 / 2 三角積分調變:是 S/N 比,標準 ADC / DAC (db):81.5 / 88 動態范圍,標準 ADC / DAC (db):82 / 87.5 電壓 - 電源,模擬:2.6 V ~ 3.3 V 電壓 - 電源,數字:1.7 V ~ 3.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-WFQFN 裸露焊盤 供應商設備封裝:48-TQFN-EP(7x7) 包裝:帶卷 (TR)
IDT821064 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:QUAD PROGRAMMABLE PCM CODEC WITH GCI INTERFACE
IDT821064PQF 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:QUAD PROGRAMMABLE PCM CODEC WITH GCI INTERFACE
IDT821068 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:OCTAL PROGRAMMABLE PCM CODEC
IDT821068PX 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:OCTAL PROGRAMMABLE PCM CODEC