- 您現在的位置：買賣IC網 > PDF目錄379206 > IBMN612804GT3B (IBM Microeletronics) 128Mb Double Data Rate Synchronous DRAM(128M位高速CMOS同步動態RAM（采用雙數據速率結構）) PDF資料下載
參數資料
| 型號： | IBMN612804GT3B |
| 廠商： | IBM Microeletronics |
| 英文描述： | 128Mb Double Data Rate Synchronous DRAM(128M位高速CMOS同步動態RAM（采用雙數據速率結構）) |
| 中文描述： | 128Mb的雙數據速率同步DRAM（128兆位高速的CMOS同步動態隨機存儲器（采用雙數據速率結構）） |
| 文件頁數： | 16/79頁 |
| 文件大?。?/td> | 1324K |
| 代理商： | IBMN612804GT3B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁
IBMN612404GT3B
IBMN612804GT3B
128Mb Double Data Rate Synchronous DRAM
Preliminary
IBM Corporation. All rights reserved.
Use is further subject to the provisions at the end of this document.
Page 16 of 79
06K0566.F39350B
1/01
Deselect
The Deselect function prevents new commands from being executed by the DDR SDRAM. The DDR SDRAM
is effectively deselected. Operations already in progress are not affected.
No Operation (NOP)
The No Operation (NOP) command is used to perform a NOP to a DDR SDRAM. This prevents unwanted
commands from being registered during idle or wait states. Operations already in progress are not affected.
Mode Register Set
The mode registers are loaded via inputs A0-A11, BA0 and BA1 while issuing the Mode Register Set Com-
mand. See mode register descriptions in the Register Definition section. The Mode Register Set command
can only be issued when all banks are idle and no bursts are in progress. A subsequent executable command
cannot be issued until t
MRD
is met.
Active
The Active command is used to open (or activate) a row in a particular bank for a subsequent access. The
value on the BA0, BA1 inputs selects the bank, and the address provided on inputs A0-A11 selects the row.
This row remains active (or open) for accesses until a Precharge (or Read or Write with Auto Precharge) is
issued to that bank. A Precharge (or Read or Write with Auto Precharge) command must be issued and com-
pleted before opening a different row in the same bank.
Read
The Read command is used to initiate a burst read access to an active (open) row. The value on the BA0,
BA1 inputs selects the bank, and the address provided on inputs A0-Ai, Aj (where [i = 9, j = don’t care] for x8;
where [i = 9, j = 11] for x4) selects the starting column location. The value on input A10 determines whether or
not Auto Precharge is used. If Auto Precharge is selected, the row being accessed is precharged at the end
of the Read burst; if Auto Precharge is not selected, the row remains open for subsequent accesses.
Write
The Write command is used to initiate a burst write access to an active (open) row. The value on the BA0,
BA1 inputs selects the bank, and the address provided on inputs A0-Ai, Aj (where [i = 9, j = don’t care] for x8;
where [i = 9, j = 11] for x4) selects the starting column location. The value on input A10 determines whether or
not Auto Precharge is used. If Auto Precharge is selected, the row being accessed is precharged at the end
of the Write burst; if Auto Precharge is not selected, the row remains open for subsequent accesses. Input
data appearing on the DQs is written to the memory array subject to the DM input logic level appearing coin-
cident with the data. If a given DM signal is registered low, the corresponding data is written to memory; if the
DM signal is registered high, the corresponding data inputs are ignored, and a Write is not executed to that
byte/column location.
Precharge
The Precharge command is used to deactivate (close) the open row in a particular bank or the open row(s) in
all banks. The bank(s) will be available for a subsequent row access a specified time (t
RP
) after the Pre-
charge command is issued. Input A10 determines whether one or all banks are to be precharged, and in the
case where only one bank is to be precharged, inputs BA0, BA1 select the bank. Otherwise BA0, BA1 are
treated as “Don’t Care.” Once a bank has been precharged, it is in the idle state and must be activated prior
to any Read or Write commands being issued to that bank. A precharge command is treated as a NOP if
there is no open row in that bank, or if the previously open row is already in the process of precharging.
相關PDF資料 |
PDF描述 |
|---|---|
| IBMN625404GT3B | 256Mb Double Data Rate Synchronous DRAM(256M位雙數據速率同步動態RAM) |
| IBMN625804GT3B | 256Mb Double Data Rate Synchronous DRAM(256M位雙數據速率同步動態RAM) |
| ICM7321 | SINGLE 12/10/8-BIT VOLTAGE-OUTPUT DACS |
| ICM7321M | SINGLE 12/10/8-BIT VOLTAGE-OUTPUT DACS |
| ICM7321MG | SINGLE 12/10/8-BIT VOLTAGE-OUTPUT DACS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IBMPPC403GAJC33C1 | 制造商:IBM 功能描述: |
| IBMPPC750CLGEQ4023 | 制造商:IBM 功能描述:MPU 750CL RISC 32BIT 90NM 400MHZ 1.15V/1.8V 278FCBGA - Trays |
| IBMPPC750CLGEQ5023 | 制造商:IBM Microelectronics 功能描述:MPU 750CL RISC 32BIT 90NM 500MHZ 1.15V/1.8V 278FCBGA - Trays |
| IBMPPC750CLGEQA033 | 制造商:IBM 功能描述:MPU 750CL RISC 32BIT 90NM 1GHZ 1.15V/1.8V 278FCBGA - Trays 制造商:IBM 功能描述:IBMIBMPPC750CLGEQA033 CPU PPC 750CL 1GHZ |
| IBN100 | 制造商:Hubbell Wiring Device-Kellems 功能描述:ICON, BLANK,BR,100PK |
發布緊急采購，3分鐘左右您將得到回復。