- 您現在的位置：買賣IC網 > PDF目錄370795 > HYE18P32160AC-15 (INFINEON TECHNOLOGIES AG) M39012 MIL RF CONNECTOR PDF資料下載
參數資料
| 型號： | HYE18P32160AC-15 |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 英文描述： | M39012 MIL RF CONNECTOR |
| 中文描述： | 32M的同步突發的CellularRAM |
| 文件頁數： | 15/53頁 |
| 文件大?。?/td> | 1426K |
| 代理商： | HYE18P32160AC-15 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
Data Sheet
15
V2.0, 2003-12-16
HYE18P32160AC(-/L)9.6/12.5/15
32M Synchronous Burst CellularRAM
Overview
Note:‘L’ represents a low voltage level, ‘H’ a high voltage level, ‘X’ represents “Don’t Care”, ‘V’ represents “Valid”.
Table 7
Description of Commands in NOR-Flash Type Mode
Mode
Description
WRITE
The WRITE command is used to perform an asynchronous write cycle. While the
address is latched by the rising edge of ADV, the data is latched by the rising
edge of either CS, WE, UB, LB, whichever comes first. The signals, UB and LB,
define whether only the lower, the upper or the whole 16-bit word is latched into
the CellularRAM.
BURST INIT
The BURST INIT command is used to initiate a synchronous burst read access
and to latch the burst start address. The burst length is determined by the bit2 -
bit0 in the Bus Configuration Register.
BURST READ
The BURST READ command is used to perform a synchronous burst read
access. The first data is output after the number of clock cycles as defined by the
programmed latency mode.
SET CONTROL REGISTER
The control registers are loaded via the address inputs A19, A15 - A0 performing
an asynchronous NOR-Flash type write access. Please refer to the control
register description for details. The SCR command can only be issued when the
CellularRAM is in idle state and no bursts are in progress.
NO OPERATION
The NOP command is used to perform a no operation to the CellularRAM, which
is selected (CS = 0). Operations already in progress are not affected.
DESELECT
The DESELECT function prevents new commands from being executed by the
CellularRAM. The CellularRAM is effectively deselected. I/O signals are put to
high impedance state.
DPD
DPD stops all refresh-related activities and entire on-chip circuit operation.
Current consumption drops below 25
μ
A. Wake-up from DPD also requires
150
μ
s to get ready for normal operation.
3) Output driver controlled by the asynchronous OE signal
4) Stand-by power mode applies only to the case when CS goes low from DESELECT while no address change occurs. NO
OPERATION from any active power mode by keeping CS low consumes the power higher than stand-by mode.
5) The asynchronous OE control signal has to be asserted to ‘H’.
6) Deep power down is maintained until control register is re-programmed to disable the bit for deep power down (RCR Bit 4).
相關PDF資料 |
PDF描述 |
|---|---|
| HYE18P32161AC-85 | 32M Asynchronous/Page CellularRAM |
| HYE18P32161AC | 32M Asynchronous/Page CellularRAM |
| HYE18P32161ACL70 | JT 23C 21#20 2#16 SKT PLUG |
| HYE18P32161ACL85 | Circular Connector; MIL SPEC:MIL-DTL-38999 Series II; Body Material:Metal; Series:JT; No. of Contacts:11; Connector Shell Size:18; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Body Style:Straight RoHS Compliant: No |
| HYE18P32161AC-70 | 32M Asynchronous/Page CellularRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HYE18P32160AC-96 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:32M Synchronous Burst CellularRAM |
| HYE18P32160ACL125 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:32M Synchronous Burst CellularRAM |
| HYE18P32160ACL15 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:32M Synchronous Burst CellularRAM |
| HYE18P32160ACL96 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:32M Synchronous Burst CellularRAM |
| HYE18P32161AC | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:32M Asynchronous/Page CellularRAM |
發布緊急采購，3分鐘左右您將得到回復。