- 您現在的位置：買賣IC網 > PDF目錄370738 > HY29LV400 4M(X8/X16)|3.0V|55|NOR FLASH - 4M PDF資料下載
參數資料
| 型號： | HY29LV400 |
| 英文描述： | 4M(X8/X16)|3.0V|55|NOR FLASH - 4M |
| 中文描述： | 4分（X8/X16）| 3.0V | 55 | NOR閃存- 4分 |
| 文件頁數： | 2/40頁 |
| 文件大小： | 550K |
| 代理商： | HY29LV400 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
2
Rev. 1.0/Nov. 01
HY29LV400
GENERAL DESCRIPTION
The HY29LV400 is a 4 Mbit, 3 volt-only, CMOS
Flash memory organized as 524,288 (512K) bytes
or 262,144 (256K) words that is available in 48-
pin TSOP and 48-ball FBGA packages. Word-
wide data (x16) appears on DQ[15:0] and byte-
wide (x8) data appears on DQ[7:0].
The HY29LV400 can be programmed and erased
in-system with a single 3 volt V
CC
supply. Inter-
nally generated and regulated voltages are pro-
vided for program and erase operations, so that
the device does not require a higher voltage V
PP
power supply to perform those functions. The de-
vice can also be programmed in standard EPROM
programmers. Access times as low as 70 ns over
the full operating voltage range of 2.7 - 3.6 volts
are offered for timing compatibility with the zero
wait state requirements of high speed micropro-
cessors. A 55 ns version operating from 3.0 to
3.6 volts is also available. To eliminate bus con-
tention, the HY29LV400 has separate chip enable
(CE#), write enable (WE#) and output enable
(OE#) controls.
The device is compatible with the JEDEC single-
power-supply Flash command set standard. Com-
mands are written to the command register using
standard microprocessor write timings. They are
then routed to an internal state-machine that con-
trols the erase and programming circuits. Device
programming is performed a byte/word at a time
by executing the four-cycle Program Command
write sequence. This initiates an internal algorithm
that automatically times the program pulse widths
and verifies proper cell margin. Faster program-
ming times can be achieved by placing the
HY29LV400 in the Unlock Bypass mode, which
requires only two write cycles to program data in-
stead of four.
The HY29LV400
’
s sector erase architecture allows
any number of array sectors to be erased and re-
programmed without affecting the data contents
of other sectors. Device erasure is initiated by
executing the Erase Command sequence. This
initiates an internal algorithm that automatically
preprograms the array (if it is not already pro-
grammed) before executing the erase operation.
As during programming cycles, the device auto-
matically times the erase pulse widths and veri-
fies proper cell margin. Hardware Sector Protec-
tion optionally disables both program and erase
operations in any combination of the sectors of
the memory array, while Temporary Sector Unpro-
tect allows in-system erasure and code changes
in previously protected sectors. Erase Suspend
enables the user to put erase on hold for any pe-
riod of time to read data from, or program data to,
any sector that is not selected for erasure. True
background erase can thus be achieved. The de-
vice is fully erased when shipped from the factory.
Addresses and data needed for the programming
and erase operations are internally latched during
write cycles, and the host system can detect
completion of a program or erase operation by
observing the RY/BY# pin, or by reading the DQ[7]
(Data# Polling) and DQ[6] (toggle) status bits.
Hardware data protection measures include a low
V
CC
detector that automatically inhibits write op-
erations during power transitions.
After a program or erase cycle has been com-
pleted, or after assertion of the RESET# pin (which
terminates any operation in progress), the device
is ready to read data or to accept another com-
mand. Reading data out of the device is similar to
reading from other Flash or EPROM devices.
Two power-saving features are embodied in the
HY29LV400. When addresses have been stable
for a specified amount of time, the device enters
the automatic sleep mode. The host can also place
the device into the standby mode. Power con-
sumption is greatly reduced in both these modes.
相關PDF資料 |
PDF描述 |
|---|---|
| HY3-9574A-9 | Analog-to-Digital Converter??? 12-Bit |
| HY3-9574B-9 | Analog-to-Digital Converter??? 12-Bit |
| HY3-9574J-5 | Analog-to-Digital Converter??? 12-Bit |
| HY3-9574K-5 | Analog-to-Digital Converter??? 12-Bit |
| HY-9574 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HY29LV400BF55 | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:4 Mbit (512K x 8/256K x 16) Low Voltage Flash Memory |
| HY29LV400BF55I | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:4 Mbit (512K x 8/256K x 16) Low Voltage Flash Memory |
| HY29LV400BF70 | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:4 Mbit (512K x 8/256K x 16) Low Voltage Flash Memory |
| HY29LV400BF70I | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:4 Mbit (512K x 8/256K x 16) Low Voltage Flash Memory |
| HY29LV400BF90 | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:4 Mbit (512K x 8/256K x 16) Low Voltage Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。