參數資料
型號： HAL805UT-E
廠商： MICRONAS SEMICONDUCTOR HOLDING AG
元件分類： 磁阻傳感器
英文描述： Programmable Linear Hall Effect Sensor
中文描述： MAGNETIC FIELD SENSOR-HALL EFFECT, -1-1mT, 0.35-4.65V, RECTANGULAR, THROUGH HOLE MOUNT
封裝： PLASTIC, TO-92UT, 3 PIN
文件頁數： 9/24頁
文件大?。?/td> 373K
代理商： HAL805UT-E
PRELIMINARY DATA SHEET
HAL805
Micronas
9
Clamping Voltage
The output voltage range can be clamped in order to
detect failures like shorts to V
DD
or GND or an open
circuit.
The CLAMP-LOW register contains the parameter for
the lower limit. The lower clamping voltage is program-
mable between 0 V and V
DD
/2. For V
DD
= 5 V, the reg-
ister can be changed in steps of 2.44 mV.
The CLAMP-HIGH register contains the parameter for
the upper limit. The upper clamping voltage is pro-
grammable between 0 V and V
DD
. For V
DD
= 5 V, in
steps of 2.44 mV.
LOCKR
By setting this 1-bit register, all registers will be locked,
and the sensor will no longer respond to any supply
voltage modulation.
Warning:
This register cannot be reset!
ADC-READOUT
This 14-bit register delivers the actual digital value of
the applied magnetic field before the signal process-
ing. This register can be read out and is the basis for
the calibration procedure of the sensor in the system
environment.
2.3. Calibration Procedure
2.3.1. General Procedure
For calibration in the system environment, the applica-
tion kit from Micronas is recommended. It contains the
hardware for the generation of the serial telegram for
programming and the corresponding software for the
input of the register values.
In this section, programming of the sensor using this
programming tool is explained. Please refer to
Section 5. on page 19 for information about program-
ming without this tool.
For the individual calibration of each sensor in the cus-
tomer application, a two point adjustment is recom-
mended (see Fig. 2
–
7 for an example). When using
the application kit, the calibration can be done in three
steps:
Step 1: Input of the registers which need not be
adjusted individually
The magnetic circuit, the magnetic material with its
temperature characteristics, the filter frequency, and
low and high clamping voltage are given for this appli-
cation.
Therefore, the values of the following registers should
be identical for all sensors of the customer application.
–
FILTER
(according to the maximum signal frequency)
–
RANGE
(according to the maximum magnetic field at the
sensor position)
–
TC and TCSQ
(depends on the material of the magnet and the
other temperature dependencies of the application)
–
CLAMP-LOW and CLAMP-HIGH
(according to the application requirements)
Write the appropriate settings into the HAL 805 regis-
ters.
相關PDF資料
PDF描述
HAL805UT-K Programmable Linear Hall Effect Sensor
HAL815 Programmable Linear Hall Sensor
HAL815A Programmable Linear Hall Sensor
HAL815E Programmable Linear Hall Sensor
HAL815K Programmable Linear Hall Sensor
相關代理商/技術參數
參數描述
HAL805UT-K 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Programmable Linear Hall Effect Sensor
HAL810 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Programmable Linear Hall-Effect Sensor
HAL815 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Programmable Linear Hall Sensor
HAL815_1 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Programmable Linear Hall-Effect Sensor
HAL815A 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Programmable Linear Hall Sensor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*