參數資料
型號: FX579
英文描述: Half Duplex GMSK Modem
中文描述: 半雙工GMSK調制解調器
文件頁數: 8/23頁
文件大?。?/td> 582K
代理商: FX579
Half Duplex GMSK Modem
FX579
1996 Consumer Microcircuits Limited
8
D/579/4
Note:
(1)
Device operation is not guaranteed for operation above 40kbits/sec or below
4kbits/sec.
If a suitable Xtal or clock signal is not supplied, device supply current may
increase.
(2)
Transmit Signal Path
The binary data applied to the DATAIO input is retimed within the chip on each rising edge of the Tx
clock and then converted into a 1V pk-pk binary signal centred around V
BIAS
. This signal is then
connected to the input of the low pass Tx filter, and the output connected to the TXOP pin.
The Tx filter has a low pass frequency response, which is approximately Gaussian in shape, as shown
in Figure 4. This minimises amplitude and phase distortion of the binary signal while providing sufficient
attenuation of the high frequency components, which would otherwise cause interference into adjacent
radio channels.
The actual filter bandwidth to be used in any particular application will be determined by the overall
system requirements. The attenuation versus frequency response of the transmit filtering provided by
this chip has been designed to meet the specifications for most GMSK modem systems, having a -3dB
bandwidth switchable between 0.3 and 0.5 times the data bit rate.
Note that an external RC network is required between the TXOP pin and the input to the frequency
modulator. This network, which can form part of any dc level shifting and gain adjustment circuitry,
forms an important part of the transmit signal filtering, and the ground connection to the capacitor
should be positioned to give maximum attenuation of high frequency noise into the modulator. The
component values should be chosen so that the product of the resistance (in Ohms) and the
capacitance (in Farads) is:
0.34 / bit rate for BT of 0.3
0.21 / bit rate for BT of 0.5
(bit rate in bits per second)
Suitable values for common bit rates are given in Table 2
Data Rate
4800 bits/sec
8000 bits/sec
9600 bits/sec
19 200 bits/sec
32 000 bits/sec
32 000 bits/sec
38 400 bits/sec
38 400 bits/sec
BT
0.5
0.3
0.5
0.5
0.3
0.5
0.3
0.5
R2
C7
91.0 k
91.0 k
47.0 k
91.0 k
47.0 k
47.0 k
47.0 k
47.0 k
470pF
470pF
470pF
120pF
220pF
150pF
180pF
120pF
Table 2 Filter Bandwidth Selection
The TXOP signal is centred around V
BIAS
, going positive for logic "1" level inputs to the DATAIO input
and negative for logic "0" inputs. Note that when in receive mode the input of the internal buffer
amplifier driving the TXOP pin is connected to V
BIAS
.
Figure 5 shows typical transmit eye patterns (measured after the external RC network) for BT values of
0.3 and 0.5
Figure 6 shows the transmit output spectrum (measured after the external RC network) again for BT
values of 0.3 and 0.5.
相關PDF資料
PDF描述
FX601A Monostable Multivibrator
FX601R Analog IC
FX601 Ultrahigh-Speed Switching Applications
FX6A-20S-0.8SV 0.8mm Pitch Stacking Height 5 to 9mm Connector
FX6-100S-0.8SV 0.8mm Pitch Stacking Height 5 to 9mm Connector
相關代理商/技術參數
參數描述
FX579D4 制造商:CMLMICRO 制造商全稱:CML Microcircuits 功能描述:HALF DUPLEX GMSK MODEM
FX5800-TD 制造商:Micro-Star International 功能描述:GF FX 5800 128MB 8X AGP - Bulk
FX5-80P-SH 功能描述:CONN HEADER 80POS 1MM R/A GOLD RoHS:否 類別:連接器,互連式 >> 板對板 - 陣列,邊緣類型,包廂 系列:FX5 標準包裝:3,000 系列:SlimStack™ 502396 連接器類型:插頭,外罩觸點 位置數:100 間距:0.016"(0.40mm) 行數:2 安裝類型:表面貼裝 特點:固定焊尾 觸點表面涂層:金 觸點涂層厚度:8µin(0.20µm) 包裝:帶卷 (TR) 配接層疊高度:2.5mm 板上方高度:0.084"(2.13mm) 其它名稱:502396-1010
FX5-80P-SH(71) 功能描述:板對板與夾層連接器 HDR 80P 1MM R/A GOLD RoHS:否 制造商:JAE Electronics 系列:WP3 產品類型:Receptacles 節距:0.4 mm 疊放高度:1 mm 安裝角: 位置/觸點數量:50 排數:2 外殼材料:Plastic 觸點材料:Copper Alloy 觸點電鍍:Gold 電壓額定值:50 V 電流額定值:0.4 A
FX5-80P-SH(72) 功能描述:板對板與夾層連接器 80P R/A SMT HEADER LOC BOSS GLD PLT RoHS:否 制造商:JAE Electronics 系列:WP3 產品類型:Receptacles 節距:0.4 mm 疊放高度:1 mm 安裝角: 位置/觸點數量:50 排數:2 外殼材料:Plastic 觸點材料:Copper Alloy 觸點電鍍:Gold 電壓額定值:50 V 電流額定值:0.4 A