參數資料
型號： FX579
英文描述： Half Duplex GMSK Modem
中文描述： 半雙工GMSK調制解調器
文件頁數： 18/23頁
文件大小： 582K
代理商： FX579
Half Duplex GMSK Modem
FX579
1996 Consumer Microcircuits Limited
18
D/579/4
b)
Bandwidth and phase response of the Rx IF filters.
c)
Accuracy of the Tx and Rx carrier frequencies.
(Any difference will shift the received signal towards one of the skirts of the IF filter
response.)
AC Coupling of Tx and Rx Signals
Ideally, the transmit path to the modulator should be dc coupled. Similarly, the Rx demodulated signal
after external adjustment should be dc coupled to the FX579 RXIN pin, providing a signal symmetrically
centred about V
BIAS
. Figure 9 shows the bit error rate (BER) performance under these conditions for
BT values of 0.3 and 0.5 in peak averaging mode. However, practical applications may require ac
coupling from the FX579's transmit output to the frequency modulator and between the receiver's
frequency discriminator and the FX579's receive input. This creates two problems:
a)
AC coupling of the signal will degrade the FX579's bit error rate (BER) performance, as shown
in Figure 10 for a data rate of 8kbits/sec, with V
DD
= 5V and BT = 0.3.
b)
AC coupling at the receive input will transform a step in the voltage at the discriminator output
to a slowly decaying pulse which can confuse the FX579's level measuring circuits. Sufficient
time should therefore be allowed for the signal into the FX579 to settle before the ACQUIRE
line is activated.
It is recommended that a data message does not contain long sequences of consecutive ones or
zeroes and that the Tx and Rx path frequency responses have cut off frequencies of
≤
5Hz and
≤
20Hz
respectively, for a data rate of 8kbits/sec and BT = 0.3.
Two-Point Modulation
When designing the FX579 into a radio that uses a frequency synthesiser, a two point modulation
technique is recommended. This is to prevent the radio's PLL circuitry from counteracting the
modulation process, and so provide a clean flat modulation response down to dc.
The transmit output (after the external RC) should be suitably buffered before being applied to the
radio's synthesizer. The drive should be applied to both the Voltage Controlled Oscillator and
Reference Oscillator Modulation inputs with suitable ac/dc levels and with correct phase to achieve
good cancellation of the loop's feedback and so provide a flat modulation response.
相關PDF資料
PDF描述
FX601A Monostable Multivibrator
FX601R Analog IC
FX601 Ultrahigh-Speed Switching Applications
FX6A-20S-0.8SV 0.8mm Pitch Stacking Height 5 to 9mm Connector
FX6-100S-0.8SV 0.8mm Pitch Stacking Height 5 to 9mm Connector
相關代理商/技術參數
參數描述
FX579D4 制造商:CMLMICRO 制造商全稱:CML Microcircuits 功能描述:HALF DUPLEX GMSK MODEM
FX5800-TD 制造商:Micro-Star International 功能描述:GF FX 5800 128MB 8X AGP - Bulk
FX5-80P-SH 功能描述:CONN HEADER 80POS 1MM R/A GOLD RoHS:否 類別:連接器，互連式 >> 板對板 - 陣列，邊緣類型，包廂 系列:FX5 標準包裝:3,000 系列:SlimStack™ 502396 連接器類型:插頭，外罩觸點 位置數:100 間距:0.016"（0.40mm） 行數:2 安裝類型:表面貼裝 特點:固定焊尾 觸點表面涂層:金 觸點涂層厚度:8µin（0.20µm） 包裝:帶卷 (TR) 配接層疊高度:2.5mm 板上方高度:0.084"（2.13mm） 其它名稱:502396-1010
FX5-80P-SH(71) 功能描述:板對板與夾層連接器 HDR 80P 1MM R/A GOLD RoHS:否 制造商:JAE Electronics 系列:WP3 產品類型:Receptacles 節距:0.4 mm 疊放高度:1 mm 安裝角: 位置/觸點數量:50 排數:2 外殼材料:Plastic 觸點材料:Copper Alloy 觸點電鍍:Gold 電壓額定值:50 V 電流額定值:0.4 A
FX5-80P-SH(72) 功能描述:板對板與夾層連接器 80P R/A SMT HEADER LOC BOSS GLD PLT RoHS:否 制造商:JAE Electronics 系列:WP3 產品類型:Receptacles 節距:0.4 mm 疊放高度:1 mm 安裝角: 位置/觸點數量:50 排數:2 外殼材料:Plastic 觸點材料:Copper Alloy 觸點電鍍:Gold 電壓額定值:50 V 電流額定值:0.4 A
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*