參數資料
型號： EVAL-ADUC831QSZ
廠商： Analog Devices Inc
文件頁數： 42/76頁
文件大?。?/td> 0K
描述： KIT DEV FOR ADUC831 QUICK START
產品培訓模塊： Process Control
標準包裝： 1
系列： QuickStart™ 套件
類型： MCU
適用于相關產品： ADuC831
所含物品： 評估板、電源、纜線、軟件和說明文檔
產品目錄頁面： 739 (CN2011-ZH PDF)
相關產品： ADUC831BCPZ-ND - IC MCU 62K FLASH ADC/DAC 56LFCSP
ADUC831BCPZ-REEL-ND - IC MCU 62K FLASH ADC/DAC 56LFCSP
ADUC831BSZ-REEL-ND - IC MCU 62K FLASH ADC/DAC 52MQFP
ADUC831BSZ-ND - IC ADC/DAC 12BIT W/MCU 52-MQFP
其它名稱： EVAL-ADUC831QS
EVAL-ADUC831QS-ND
REV. 0
ADuC831
–47–
8052 COMPATIBLE ON-CHIP PERIPHERALS
This section gives a brief overview of the various secondary
peripheral circuits that are also available to the user on-chip.
These remaining functions are mostly 8052 compatible (with a
few additional features) and are controlled via standard 8052
SFR bit definitions.
Parallel I/O
The ADuC831 uses four input/output ports to exchange data
with external devices. In addition to performing general-purpose
I/O, some ports are capable of external memory operations while
others are multiplexed with alternate functions for the peripheral
features on the device. In general, when a peripheral is enabled,
that pin may not be used as a general-purpose I/O pin.
Port 0
Port 0 is an 8-bit, open-drain, bidirectional I/O port that is directly
controlled via the Port 0 SFR. Port 0 is also the multiplexed
low-order address and data bus during accesses to external pro-
gram or data memory.
Figure 36 shows a typical bit latch and I/O buffer for a Port 0
port pin. The bit latch (one bit in the port’s SFR) is represented
as a Type D flip-flop, which will clock in a value from the inter-
nal bus in response to a “write to latch” signal from the CPU.
The Q output of the flip-flop is placed on the internal bus in
response to a “read latch” signal from the CPU. The level of the
port pin itself is placed on the internal bus in response to a
“read pin” signal from the CPU. Some instructions that read a
port activate the “read latch” signal, and others activate the
“read pin” signal. See the following Read-Modify-Write Instruc-
tions section for more details.
CONTROL
READ
LATCH
INTERNAL
BUS
WRITE
TO LATCH
READ
PIN
D
CL
Q
LATCH
DVDD
ADDR/DATA
P0.x
PIN
Figure 36. Port 0 Bit Latch and I/O Buffer
As shown in Figure 36, the output drivers of Port 0 pins are
switchable to an internal ADDR and ADDR/DATA bus by an
internal CONTROL signal for use in external memory accesses.
During external memory accesses the P0 SFR gets 1s written to it
(i.e., all of its bit latches become 1). When accessing external
memory, the CONTROL signal in Figure 36 goes high, enabling
push-pull operation of the output pin from the internal address or
data bus (ADDR/DATA line). Therefore, no external pull-ups are
required on Port 0 in order for it to access external memory.
In general-purpose I/O port mode, Port 0 pins that have 1s written
to them via the Port 0 SFR will be configured as “open drain”
and will therefore float. In this state, Port 0 pins can be used as
high impedance inputs. This is represented in Figure 36 by the
NAND gate whose output remains high as long as the CONTROL
signal is low, thereby disabling the top FET. External pull-up
resistors are therefore required when Port 0 pins are used as
general-purpose outputs. Port 0 pins with 0s written to them
will drive a logic low output voltage (VOL) and will be capable of
sinking 1.6 mA.
Port 1
Port 1 is also an 8-bit port directly controlled via the P1 SFR.
Port 1 digital output capability is not supported on this device.
Port 1 pins can be configured as digital inputs or analog inputs.
By (power-on) default these pins are configured as analog
inputs, i.e., 1 written in the corresponding Port 1 register bit.
To configure any of these pins as digital inputs, the user should
write a 0 to these port bits to configure the corresponding pin as
a high impedance digital input.
These pins also have various secondary functions described in
Table XVII.
Table XVII. Port 1, Alternate Pin Functions
Pin
Alternate Function
P1.0
T2 (Timer/Counter 2 External Input)
P1.1
T2EX (Timer/Counter 2 Capture/Reload Trigger)
P1.5
SS (Slave Select for the SPI Interface)
READ
LATCH
INTERNAL
BUS
WRITE
TO LATCH
READ
PIN
D
CL
Q
LATCH
P1.x
PIN
TO ADC
Figure 37. Port 1 Bit Latch and I/O Buffer
Port 2
Port 2 is a bidirectional port with internal pull-up resistors
directly controlled via the P2 SFR. Port 2 also emits the high
order address bytes during fetches from external program memory
and middle and high order address bytes during accesses to the
24-bit external data memory space.
As shown in Figure 38, the output drivers of Ports 2 are switchable
to an internal ADDR and ADDR/DATA bus by an internal
CONTROL signal for use in external memory accesses (as for
Port 0). In external memory addressing mode (CONTROL = 1)
the port pins feature push-pull operation controlled by the inter-
nal address bus (ADDR line). However, unlike the P0 SFR
during external memory accesses, the P2 SFR remains unchanged.
相關PDF資料
PDF描述
HMM08DRKI CONN EDGECARD 16POS DIP .156 SLD
0210490856 CABLE JUMPER 1.25MM .051M 17POS
EVAL-ADUC7028QSZ KIT DEV ADUC7028 QUICK START
GMM12DREN CONN EDGECARD 24POS .156 EYELET
GSM12DREH CONN EDGECARD 24POS .156 EYELET
相關代理商/技術參數
參數描述
EVAL-ADUC832QS 制造商:Analog Devices 功能描述:QUICK START DEVELOPMENT SYSTEM - Bulk 制造商:Analog Devices 功能描述:DEVELOPMENT KIT SYSTEM
EVAL-ADUC832QSZ 功能描述:KIT DEV FOR ADUC832 QUICK START RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ 套件 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF)
EVAL-ADUC834QS 制造商:Analog Devices 功能描述:DATA ACQ SYS, MICROCNVRTR, DUAL 16BIT/24BIT - ADCS W/ EMBEDD - Bulk 制造商:Analog Devices 功能描述:8052 ADUC834 QUICKSTART DEV KIT
EVAL-ADUC834QSZ 功能描述:KIT DEV QUICK START ADUC834 RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ 套件 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF)
EVAL-ADUC836QS 制造商:Analog Devices 功能描述:MCU 8BIT 8052 CISC 62KB+4KB FLASH 3.6V 48LQFP - Bulk 制造商:Analog Devices 功能描述:KIT- ADUC836 DEV SYSTEM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*