- 您現在的位置：買賣IC網 > PDF目錄15529 > EVAL-ADAU1701MINIZ (Analog Devices Inc)BOARD EVAL SIGMADSP AUD ADAU1701 PDF資料下載
參數資料
| 型號： | EVAL-ADAU1701MINIZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 21/53頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL SIGMADSP AUD ADAU1701 |
| 標準包裝： | 1 |
| 系列： | SigmaDSP® |
| 類型： | DSP：音頻 |
| 適用于相關產品： | ADAU1701 |
| 所含物品： | 板，線纜 |
| 產品目錄頁面： | 776 (CN2011-ZH PDF) |
| 相關產品： | ADAU1701JSTZ-RL-ND - IC AUDIO PROC 2ADC/4DAC 48-LQFP ADAU1701JSTZ-ND - IC AUDIO PROC 2ADC/4DAC 48-LQFP |
| 其它名稱： | ADAU1701MINIBZ ADAU1701MINIBZ-ND ADAU1701MINIZ ADAU1701MINIZ-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
ADAU1701
Rev. B | Page 27 of 52
SELF-BOOT
On power-up, the ADAU1701 can load a program and a set
of parameters that have been saved in an external EEPROM.
Combined with the auxiliary ADC and the multipurpose pins,
this eliminates the need for a microcontroller in the system. The
self-booting is accomplished by the ADAU1701 acting as a master
on the I2C bus on startup, which occurs when the SELFBOOT
pin is set high. The ADAU1701 cannot self-boot in SPI mode.
The maximum necessary EEPROM size for program and
parameters is 9248 bytes, or just over 8.5 kB. This does not
include register settings or overhead bytes, but such factors do
not add a significant number of bytes. This much memory is
only needed if the program RAM (1024 × five bytes), parameter
RAM (1024 × four bytes), and interface registers (8 × four bytes)
are completely full. Most applications do not use the full program
and parameter RAMs, so an 8 kB EEPROM should be sufficient.
A self-boot operation is triggered on the rising edge of RESET
when the SELFBOOT and WP pins are set high. The ADAU1701
reads the program, parameters, and register settings from the
EEPROM. After the ADAU1701 finishes self-booting, additional
messages can be sent to the ADAU1701 on the I2C bus, although
this typically is not necessary in a self-booting application. The
I2C device address is 0x68 for a write and 0x69 for a read in this
mode. The ADDRx pins have different functions when the chip
is in this mode, so the settings on them can be ignored.
The ADAU1701 does not self-boot if WP is set low. Holding
this pin low allows the EEPROM to be programmed in-circuit.
The WP pin is pulled low (it typically has a resistor pull-up) to
enable writes to the EEPROM, but this in turn disables the self-
boot function until the WP pin is returned high.
The ADAU1701 is a master on the I2C bus during self-boot and
writeback. Although it is uncommon for an application using
self-boot to also have a microcontroller connected to the control
lines, care should be taken that no other device tries to write to the
I2C bus during self-boot or writeback. The ADAU1701 generates
SCL at 8 × fS; therefore, for a fS of 48 kHz, SCL runs at 384 kHz.
SCL has a duty cycle of 3/8 in accordance with the I2C specification.
The ADAU1701 reads from EEPROM Chip Address 0xA1. The
LSBs of the addresses of some EEPROMs are pin configurable;
in most cases, these pins should be tied low to set this address.
EEPROM Format
The EEPROM data contains a sequence of messages. Each
discrete message is one of the seven types defined in Table 19
and consists of a sequence of one or more bytes. The first byte
identifies the message type. Bytes are written MSB first. Most
messages are block write (0x01) types, which are used for writing
to the ADAU1701 program RAM, parameter RAM, and control
registers.
The body of the message following the message type should
start with a 0x00 byte; this is the chip address. As with all other
control port transactions, following the chip address is a 2-byte
register/memory address field.
Figure 28 shows an example of what should be stored in the
EEPROM, starting with EEPROM Address 0. In this example,
the interface registers are first set to control port write mode
(Line 1), which is followed by 18 no-operation (no-op) bytes
(Line 2 to Line 4) so that the interface register data appears on
Page 2 of the EEPROM. Next follows the write header (Line 4)
and then 32 bytes of interface register data (Line 5 to Line 8).
Finally, the program RAM data, starting at ADAU1701 Address
0x04 0x00 is written (Line 9 to Line 11). In this example, the
program length is 70 words, or 350 bytes, so 332 more bytes are
included in the EEPROM but are not shown in Figure 28.
Writeback
A writeback occurs when the WB pin is triggered and data is
written to the EEPROM from the ADAU1701. This function is
typically used to save the volume setting and other parameter
settings to the EEPROM just before power is removed from the
system. A rising edge on the WB pin triggers a writeback when
the device is in self-boot mode, unless a message to set the WB
to the falling edge sensitive (0x05) is contained in the self-boot
message sequence. Only one writeback takes place unless a
message to set multiple writebacks (0x04) is contained in the
self-boot message sequence. The WP pin is pulled low when a
writeback is triggered to allow writing to the EEPROM.
The ADAU1701 is only capable of writing back the contents of
the interface registers to the EEPROM. These registers are usually
set by the DSP program, but can also be written to directly after
setting Bit 6 of the core control register. The parameter settings
that should be saved are configured in SigmaStudio.
相關PDF資料 |
PDF描述 |
|---|---|
| RBA15DTMI | CONN EDGECARD 30POS R/A .125 SLD |
| V300C24C75BF2 | CONVERTER MOD DC/DC 24V 75W |
| BQ2057DGKRG4 | IC LI-ION LDO CHRG MGMT 8-MSOP |
| AIUR-06-821K | INDUCTOR POWER 820UH 10% T/H |
| RBA15DTBI | CONN EDGECARD 30POS R/A .125 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADAU1701MINIZ | 制造商:Analog Devices 功能描述:ADAU1701MINIZ EvaluationBoard |
| EVAL-ADAU1702EB | 制造商:AD 制造商全稱:Analog Devices 功能描述:SigmaDSP 28-56-Bit Audio Processor with Two ADCs and Four DACs |
| EVAL-ADAU1702EBZ | 制造商:Analog Devices 功能描述:EVALBRD SIGMADSP28/56-B AUDIOPR2ADC/4DAC - Bulk |
| EVAL-ADAU1761Z | 功能描述:BOARD EVAL FOR ADAU1761 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:SigmaDSP® 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源 |
| EVAL-ADAU1781Z | 功能描述:BOARD EVAL FOR ADAU1781 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:SigmaDSP® 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
發布緊急采購，3分鐘左右您將得到回復。