- 您現在的位置：買賣IC網 > PDF目錄364747 > ES29DL320 (優先(蘇州)半導體有限公司) 32Mbit(4M x 8/2M x 16) CMOS 3.0 Volt-only, Simultaneous Operation Flash Memory PDF資料下載
參數資料
| 型號： | ES29DL320 |
| 廠商： | 優先(蘇州)半導體有限公司 |
| 元件分類： | FLASH |
| 英文描述： | 32Mbit(4M x 8/2M x 16) CMOS 3.0 Volt-only, Simultaneous Operation Flash Memory |
| 中文描述： | 32兆位（4M×8/2M×16），3.0伏，CMOS，同時運行閃存 |
| 文件頁數： | 27/59頁 |
| 文件大小： | 791K |
| 代理商： | ES29DL320 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
ESI
27
Rev. 0E May 25, 2006
ES29DL320
Excel Semiconductor inc.
ADVANCED INFORMATION
Sector Erase Time-out Window and DQ3
After the command sequence is written, a sector
erase time-out of
50us
occurs. During the time-out
period, additional sector addresses and sector
erase commands may be written. Loading the sec-
tor erase buffer may be done in any sequence, and
the number of sectors may be from one sector to all
sectors. The time between these additional cycles
must be less than 50us, otherwise the last address
and command may not be accepted, and erasure
may begin. It is recommended that processor inter-
rupts be disabled during this time to ensure all com-
mands are accepted. The interrupts can be re-
enabled after the last Sector Erase command is
written. The system can monitor
DQ3
to determine
if the sector erase timer has timed out (See the sec-
tion on DQ3:Sector Erase Timer.). The time-out
begins from the rising edge of the final WE# pulse
in the command sequence.
Any command other than Sector Erase or Erase
Suspend during the time-out period resets that
bank to the read mode. The system must rewrite
the command sequence and any additional
addresses and commands.
Status Bits : DQ7,DQ6,DQ2, or RY/BY#
When the Sector Erase Embedded Erase algorithm
is complete, the bank returns to reading array data
and addresses are no longer latched. Note that while
the Embedded Erase operation is in progress, the
system can read data from the non-erasing bank.
The system can determine the status of the erase
operation by reading DQ7,DQ6,DQ2, or RY/BY# in
the erasing bank. Refer to the Write Operation Status
section Table 10 for information on these status bits.
Valid Command during Sector Erase
Once the sector erase operation has begun, only the
Erase Suspend command is valid. All other com-
mands are ignored. However, note that a
hardware
reset
immediately terminates the erase operation. If
that occurs, the sector erase command sequence
should be reinitiated once that bank has returned to
reading array data, to ensure data integrity.
Fig. 9 illustrates the algorithm for the erase opera-
tion. Refer to the Erase and Program Operations
tables in the AC Characteristics section for parame-
ters, and Fig. 23 section for timing diagrams.
ERASE SUSPEND/ERASE RESUME
An erase operation is a long-time operation so that
two useful commands are provided in the
ES29DL320 device Erase Suspend and Erase
Resume Commands. Through the two commands,
erase operation can be suspended for a while and
the suspended operation can be resumed later when
it is required. While the erase is suspended, read or
program operations can be performed by the system.
Erase Suspend Command, (B0h)
The Erase Suspend command, B0h, allows the sys-
tem to interrupt a sector erase operation and then
read data from, or program data to, any sector not
selected for erasure. The bank address is required
when writing this command. This command is valid
only during the sector erase operation, including the
50us time-out
period during the sector erase com-
mand sequence. The Erase Suspend command is
ignored if written during the chip erase operation or
Embedded Program algorithm. When the Erase Sus-
pend command is written during the sector erase
operation, the device requires a maximum of
20us
to
suspend the erase operation. However, when the
Erase Suspend command is written during the sector
erase time-out, the device immediately terminates
the time-out period and suspends the erase opera-
tion.
Figure 9. Erase Operation
Notes:
1. See Table 9 for erase command sequence
2. See the section on DQ3 for information on the sector erase timer
START
No
Yes
Write Erase
Command Sequence
(Notes 1,2)
Data Poll to
Erasing Bank
from System
Data = FFh
Erasure Completed
Embedded
Erase
algorithm in
progress
相關PDF資料 |
PDF描述 |
|---|---|
| ES3A | Surface Mount Ultrafast Efficient Plastic Rectifier(表貼型超快速效應塑膠整流器) |
| ES3B | Surface Mount Ultrafast Efficient Plastic Rectifier(表貼型超快速效應塑膠整流器) |
| ES3C | Surface Mount Ultrafast Efficient Plastic Rectifier(表貼型超快速效應塑膠整流器) |
| ES3D | Surface Mount Ultrafast Efficient Plastic Rectifier(表貼型超快速效應塑膠整流器) |
| ES3F | Surface Mount Ultrafast Efficient Plastic Rectifier(表貼型超快速效應塑膠整流器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ES29DL320D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:32Mbit(4M x 8/2M x 16) CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| ES29DL320D-12RTG | 制造商:EXCELSEMI 制造商全稱:EXCELSEMI 功能描述:32Mbit(4M x 8/2M x 16) CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| ES29DL320D-70TG | 制造商:EXCELSEMI 制造商全稱:EXCELSEMI 功能描述:8Mbit(1M x 8/512K x 16) CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| ES29DL320D-70WC | 制造商:EXCELSEMI 制造商全稱:EXCELSEMI 功能描述:8Mbit(1M x 8/512K x 16) CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| ES29DL320D-90RTG | 制造商:EXCELSEMI 制造商全稱:EXCELSEMI 功能描述:8Mbit(1M x 8/512K x 16) CMOS 3.0 Volt-only, Boot Sector Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。