
ESI
                                   23
Rev. 0E May 25, 2006
ES29DL320
Excel Semiconductor inc.
ADVANCED INFORMATION
Table 9.  ES29DL320 Command Definitions
Command Definitions
Command
Sequence
(Note 1)
C
Bus Cycles (Notes 2~5)
First
Second
Third
Fourth
Fifth
Sixth
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Read (Note 6)
1
RA
RD
Reset (Note 7)
1
XXX
F0
A
Manufacturer ID
Word
4
555
AA
2AA
55
(BA)555
90
(BA)X00
4A
Byte
AAA
555
(BA)AAA
Device ID
Word
4
555
AA
2AA
55
(BA)555
90
(BA)X01
41/81
Byte
AAA
555
(BA)AAA
(BA)X02
Security Sector Fac
tory Protect (Note10)
Word
4
555
AA
2AA
55
(BA)555
90
(BA)X03
82/02
Byte
AAA
555
(BA)AAA
(BA)X06
Sector Protect Verify
(Note 11)
Word
4
555
AA
2AA
55
(BA)555
90
(SA)X02
00/01
Byte
AAA
555
(BA)AAA
(SA)X04
Enter Security Sector Region
Word
3
555
AA
2AA
55
555
88
Byte
AAA
555
AAA
Exit Security Sector Region
Word
4
555
AA
2AA
55
555
90
XXX
00
Byte
AAA
555
AAA
Program
Word
4
555
AA
2AA
55
555
A0
PA
PD
Byte
AAA
555
AAA
Unlock Bypass
Word
3
555
AA
2AA
55
555
20
Byte
AAA
555
AAA
Unlock Bypass Program (Note 12)
2
XXX
A0
PA
PD
Unlock Bypass Reset (Note 13)
2
XXX
90
XXX
00
Chip Erase
Word
6
555
AA
2AA
55
555
80
555
AA
2AA
55
555
10
Byte
AAA
555
AAA
AAA
555
AAA
Sector Erase
Word
6
555
AA
2AA
55
555
80
555
AA
2AA
55
SA
30
Byte
AAA
555
AAA
AAA
555
Erase Suspend (Note 14)
1
XXX
B0
Erase Resume (Note 15)
1
XXX
30
CFI Query (Note 16)
Word
1
55
98
Byte
AA
Legend:
X = Don’t care
RA = Address of the memory location to be read.
RD = Data read from location RA during read operation
PA = Address of the memory location to be programmed.
Addresses latch on the falling edge of the WE# or CE# pulse,
whichever happens later.
PD = Data to be programmed at location PA. Data latches on the
rising edge of  WE# or CE# pulse, whichever happens first.
SA = Address of the sector to be verified (in autoselect mode) or
erased. Address bits A20-A12 uniquely select any sector.
BA = Address of the bank that is being switched to autoselect
mode, is in bypass mode, or is being erased.
 9. The device ID is 41h for top boot device, and 81h for bottom
boot device. 
10. The data is 82h for factory locked and 02h for not  
factory 
       locked.
11. The data is 00h for an unprotected sector and 01h for a 
       protected  sector.
12. The Unlock Bypass command is required prior to the Unlock-
      Bypass Program command.
13. The Unlock Bypass Reset command is required to return 
      to the read mode when the bank is in the unlock bypass 
      mode.
14. The system may read and program in non-erasing sectors, 
      or enter the autoselect mode, when in the Erase  Suspend 
      mode. The Erase Suspend command is valid only during 
     a sector erase operation, and requires the bank address.
15. The Erase Resume command is valid only during the Erase 
      Suspend mode, and requires the bank address.
16. Command is valid when device is ready to read array data 
      or when device is in autoselect mode.
Notes:
1. See Table 1 for description of bus operations.
2. All values are in hexadecimal.
3. Except for the read cycle and the fourth cycle of the autoselect     
    command sequence, all bus cycles are write cycles.
4. Data bits DQ15-DQ8 are don’t care in command sequences,
    except for RD and PD
5. Unless otherwise noted, address bits A20-A11 are don’t cares.
6. No unlock or command cycles required when bank is in 
    read mode.
7. The Reset command is required to return to the read mode 
    (or to the erase-suspend-read mode if previously in Erase 
    Suspend) when a bank is in the autoselect mode, or if DQ5 
    goes high (while the bank is providing status information).
8. The fourth cycle of the autoselect command sequence 
    is a read cycle. The system must provide the bank address
    to obtain the manufacturer ID, device ID, or SecSi Sector
    factory protect information. Data bits DQ15-DQ8 are 
    don’t care. See the  Autoselect Command Sequence section
    for more information.