The SHI has five I/O" />
參數資料
型號： DSPB56367AG150
廠商： Freescale Semiconductor
文件頁數： 8/100頁
文件大?。?/td> 0K
描述： IC DSP 24BIT 150MHZ 144-LQFP
標準包裝： 60
系列： DSP56K/Symphony
類型： 音頻處理器
接口： 主機接口，I²C，SAI，SPI
時鐘速率： 150MHz
非易失內存： ROM（240 kB）
芯片上RAM： 69kB
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 1.80V
工作溫度： -40°C ~ 95°C
安裝類型： 表面貼裝
封裝/外殼： 144-LQFP
供應商設備封裝： 144-LQFP（20x20）
包裝： 托盤
Serial Host Interface
DSP56367 Technical Data, Rev. 2.1
Freescale Semiconductor
2-11
2.11
Serial Host Interface
The SHI has five I/O signals that can be configured to allow the SHI to operate in either SPI or I2C mode.
Table 2-10 Serial Host Interface Signals
Signal
Name
Signal
Type
State During
Reset
Signal Description
SCK
SCL
Input or
Output
Input or
Output
Tri-Stated
SPI Serial Clock—The SCK signal is an output when the SPI is configured as a
master and a Schmitt-trigger input when the SPI is configured as a slave. When the
SPI is configured as a master, the SCK signal is derived from the internal SHI clock
generator. When the SPI is configured as a slave, the SCK signal is an input, and
the clock signal from the external master synchronizes the data transfer. The SCK
signal is ignored by the SPI if it is defined as a slave and the slave select (SS) signal
is not asserted. In both the master and slave SPI devices, data is shifted on one
edge of the SCK signal and is sampled on the opposite edge where data is stable.
Edge polarity is determined by the SPI transfer protocol.
I2C Serial Clock—SCL carries the clock for I2C bus transactions in the I2C mode.
SCL is a Schmitt-trigger input when configured as a slave and an open-drain output
when configured as a master. SCL should be connected to VCC through a pull-up
resistor.
This signal is tri-stated during hardware, software, and individual reset. Thus, there
is no need for an external pull-up in this state.
This input is 3.3V tolerant.
MISO
SDA
Input or
Output
Input or
Open-Drain
Output
Tri-Stated
SPI Master-In-Slave-Out—When the SPI is configured as a master, MISO is the
master data input line. The MISO signal is used in conjunction with the MOSI signal
for transmitting and receiving serial data. This signal is a Schmitt-trigger input when
configured for the SPI Master mode, an output when configured for the SPI Slave
mode, and tri-stated if configured for the SPI Slave mode when SS is deasserted.
An external pull-up resistor is not required for SPI operation.
I2C Data and Acknowledge—In I2C mode, SDA is a Schmitt-trigger input when
receiving and an open-drain output when transmitting. SDA should be connected to
VCC through a pull-up resistor. SDA carries the data for I
2C transactions. The data
in SDA must be stable during the high period of SCL. The data in SDA is only
allowed to change when SCL is low. When the bus is free, SDA is high. The SDA
line is only allowed to change during the time SCL is high in the case of start and
stop events. A high-to-low transition of the SDA line while SCL is high is a unique
situation, and is defined as the start event. A low-to-high transition of SDA while
SCL is high is a unique situation defined as the stop event.
This signal is tri-stated during hardware, software, and individual reset. Thus, there
is no need for an external pull-up in this state.
This input is 3.3V tolerant.
相關PDF資料
PDF描述
DSPB56371AF180 IC DSP 24BIT 180MHZ 80-LQFP
DSPB56374AEC IC DSP 24BIT 150MHZ 52-LQFP
DSPB56720CAG DSP 24BIT AUD 200MHZ 144-LQFP
DSPB56724AG DSP 24BIT AUD 250MHZ 144-LQFP
DSPIC30F2010T-20E/MM IC DSPIC MCU/DSP 12K 28QFN
相關代理商/技術參數
參數描述
DSPB56367PV150 功能描述:數字信號處理器和控制器 - DSP, DSC 150Mhz/ 150MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPB5636AG120 制造商:Freescale Semiconductor 功能描述:
DSPB56371AF150 功能描述:數字信號處理器和控制器 - DSP, DSC 150 MHZ VERSION DSPB371 RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPB56371AF180 功能描述:數字信號處理器和控制器 - DSP, DSC BLANK ROM VERSION 56371 RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPB56371AF180 制造商:Freescale Semiconductor 功能描述:Digital Signal Processor (DSP) IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*