- 您現在的位置：買賣IC網 > PDF目錄385273 > DS26303L-75 (MAXIM INTEGRATED PRODUCTS INC) 3.3V, E1/T1/J1, Short-Haul, Octal Line Interface Unit PDF資料下載
參數資料
| 型號： | DS26303L-75 |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | 3.3V, E1/T1/J1, Short-Haul, Octal Line Interface Unit |
| 中文描述： | DATACOM, PCM TRANSCEIVER, PQFP144 |
| 封裝： | 20 X 20 MM, 1.40 MM HEIGHT, MS-026, LQFP-144 |
| 文件頁數： | 61/97頁 |
| 文件大小： | 966K |
| 代理商： | DS26303L-75 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁當前第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁
DS26303: 3.3V, T1/E1/J1, Short-Haul, Octal Line Interface Unit
61 of 97
6.4.5 Bipolar Violation and Excessive Zero Detector
The DS26303 detects code violations, BPV, and excessive zero errors. The reporting of the errors is done through
the pin RNEGn/CVn.
Excessive zeros are detected if eight consecutive 0s are detected with B8ZS enabled and four consecutive 0s are
detected with HDB3 enabled. Excessive zero detection is selectable when single-rail mode and HDB3/B8ZS
encoding/decoding is selected.
The bits in
EZDE
and
CVDEB
registers determine the combinations that are reported.
Table 6-9
outlines the
functionality:
Table 6-9. BPV, Code Violation, and Excessive Zero Error Reporting
CONDITIONS
CVn PIN REPORTS
BPV + code violation
BPV + code violation + excessive zero
BPV
BPV + excessive zero
EZDE is reset, CVDEB is reset
EZDE is set, CVDEB is reset
EZDE is reset, CVDEB is set
EZDE is set, CVDEB is set
6.4.6 LIU Receiver Front End
It is recommended that the receiver be configured as per
Table 6-4
and
Figure 6-4
. Internal or external mode for
the receiver front end can be selected by register
GC.RIMPMS
. When this bit is set to external mode the user is
required to supply two 15 resistors as shown in
Figure 6-4
. The internal adjust resistors A75, A100, and A110 will
still be set in external mode if 75 , 100 , or 110 impedance is selected during template selection. However, the
internal 30 resistor will be disconnected. If the user would like all the adjust resistors to be disconnected or any
internal impedance matching, then the user should set the
TS.RIMPOFF
bit for each LIU or the RIMPOFF pin when
in hardware mode.
6.5 Hitless-Protection Switching (HPS)
Many current redundancy protection implementations use mechanical relays to switch between primary and
backup boards. The switching time in relays is typically in the milliseconds, making T1/E1 HPS impossible. The
switching event likely causes frame-synchronization loss in any equipment downstream, affecting the quality of
service. The same is also true for tri-stating mechanisms that use software or inactive clocks for the triggering of
HPS.
The DS26303 LIU includes fast tri-statable outputs for TTIP and TRING and fast turn-off impedance matching for
the RTIP and RRING within less than one bit cycle. The control logic is shown in
Figure 6-5
. In software mode, the
user can set the RHPMC bit, which allows the OE pin to control both the transmitter outputs and the receive
impedance matching. This is a very useful function in that control can be done through a hardware pin, allowing a
quick switch to the backup system for both the receiver and the transmitter.
Figure 6-6
shows a typical HPS
application in software mode where the OE is used for control. In hardware mode, the receiver can have
impedance matching turned off quickly by using the RIMPOFF pin, and the transmitter output can be turned off
quickly by using the OE pin.
相關PDF資料 |
PDF描述 |
|---|---|
| DS26303LN-120 | 3.3V, E1/T1/J1, Short-Haul, Octal Line Interface Unit |
| DS26303LN-75 | 3.3V, E1/T1/J1, Short-Haul, Octal Line Interface Unit |
| DS26518 | 8-Port T1/E1/J1 Transceiver |
| DS26518G | 8-Port T1/E1/J1 Transceiver |
| DS26518GN | 8-Port T1/E1/J1 Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS26303L-75+ | 功能描述:電信線路管理 IC 3.3V E1/T1/J1 Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| DS26303L-75+A3 | 功能描述:電信線路管理 IC 3.3V E1/T1/J1 Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| DS26303L-75A3 | 功能描述:電信線路管理 IC 3.3V E1/T1/J1 Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| DS26303LN-120 | 功能描述:電信線路管理 IC RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| DS26303LN-120+ | 功能描述:電信線路管理 IC 3.3V E1/T1/J1 Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。