- 您現在的位置：買賣IC網 > PDF目錄376802 > DM9000 (Electronic Theatre Controls, Inc.) ISA TO ETHERNET MAC CONTROLLER WITH INTEGRATED 10/100 PHY PDF資料下載
參數資料
| 型號： | DM9000 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | ISA TO ETHERNET MAC CONTROLLER WITH INTEGRATED 10/100 PHY |
| 中文描述： | ISA以以太網MAC控制器，它集成10/100網卡芯片 |
| 文件頁數： | 31/54頁 |
| 文件大?。?/td> | 575K |
| 代理商： | DM9000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
DM9000
ISA to Ethernet MAC Controller with Integrated 10/100 PHY
Final
Version: DM9000-DS-F02
June 26, 2002
31
9. Functional Description
9.1 Host Interface
The host interface is the ISA BUS compatible mode.
There are eight IO bases, which are 300H, 310H,
320H, 330H, 340H, 350H, 360H, and 370H. The IO
base is latched from strap pins or loaded from the
EEPROM.
There are only two addressing ports through the
access of the host interface. One port is the INDEX
port and the other is the DATA port. The INDEX port is
decoded by the pin CMD =0 and the DATA port by the
pin CMD =1. The contents of the INDEX port are the
register address of the DATA port. Before the access
of any register, the address of the register must be
saved in the INDEX port.
9.2 Direct Memory Access Control
The DM9000 provides DMA capability to simplify the
access of the internal memory. After the programming
of the starting address of the internal memory and
then issuing a dummy read/write command to load the
current data to internal data buffer, the desired
location of the internal memory can be accessed by
the read/write command registers. The memory’s
address will be increased with the size that equals to
the current operation mode (i.e. the 8-bit, 16-bit or 32-
bit mode) and the data of the next location will be
loaded into internal data buffer automatically. It is
noted that the data of the first access (the dummy
read/write command) in a sequential burst should be
ignored because that the data was the contents of the
last read/write command.
The internal memory size is 16K bytes. The first
location of 3K bytes is used for the data buffer of the
packet transmission. The other 13K bytes are used for
the buffer of the receiving packets. So in the write
memory operation, when the bit 7 of IMR is set, the
memory address increment will wrap to location 0 if
the end of address (i.e. 3K) is reached. In a similar
way, in the read memory operation, when the bit 7 of
IMR is set, the memory address increment will wrap to
location 0x0C00 if the end of address (i.e. 16K) is
reached.
9.3 Packet Transmission
There are two packets, sequentially named as index I
and index II, can be stored in the TX SRAM at the
same time. The TX Control Register (02h) controls the
insertion of CRC and pads. Their statuses are
recorded at TX Status Register I (03h) and TX Status
Register II (04h) respectively.
The start address of transmission is 00h and the
current packet is index I after software or hardware
reset. Firstly write data to the TX SRAM using the
DMA port and then write the byte count to byte_ count
register at TX Packet Length Register (0fch/0fdh). Set
the bit 0 of TX Control Register (02h). The DM9000
starts to transmit the index I packet. Before the
transmission of the index I packet ends, the data of
the next (index II) packet can be moved to TX SRAM.
After the index I packet ends the transmission, write
the byte count data of the index II to BYTE_COUNT
register and then set the bit 0 of TX Control Register
(02h) to transmit the index II packet. The following
packets, named index I, II, I, II,…, use the same way
to be transmitted.
9.4 Packet Reception
The RX SRAM is a ring data structure. The start
address of RX SRAM is 0C00h after software or
hardware reset. Each packet has a 4-byte header
followed with the data of the reception packet which
CRC field is included. The format of the 4-byte header
is 01h, status, BYTE_COUNT low, and
BYTE_COUNT high. It is noted that the start address
of each packet is in the proper address boundary
which depends on the operation mode (the 8-bit, 16-
bit or 32-bit mode ).
相關PDF資料 |
PDF描述 |
|---|---|
| DM9000E | ISA TO ETHERNET MAC CONTROLLER WITH INTEGRATED 10/100 PHY |
| DM9006CJ | Gate Expander |
| DM9006CN | Gate Expander |
| DM9009CJ | Dual 4-input NAND Gate |
| DM9009CN | Dual 4-input NAND Gate |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DM9000()EVB | 制造商:DAVICOM 功能描述:BOARD EVALUATION DM9000 制造商:DAVICOM 功能描述:DM9000, MAC CNTLR, ENET, EVAL BOARD 制造商:DAVICOM 功能描述:EVAL BOARD, DM9000, MAC CNTLR, ENET; ;ROHS COMPLIANT: YES |
| DM9000_09 | 制造商:DAVICOM 制造商全稱:DAVICOM 功能描述:ISA to Ethernet MAC Controller with Integrated 10/100 PHY |
| DM9000A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Ethernet Controller with General Processor Interface 臺灣Davicom公司出品的48pin、10/100M網絡控制芯片 |
| DM9000A_06 | 制造商:DAVICOM 制造商全稱:DAVICOM 功能描述:Ethernet Controller with General Processor Interface |
| DM9000AE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Ethernet Controller with General Processor Interface |
發布緊急采購，3分鐘左右您將得到回復。