- 您現在的位置：買賣IC網 > PDF目錄380227 > CYV15G0204RB (Cypress Semiconductor Corp.) Independent Clock Dual HOTLink II⑩ Reclocking Deserializer PDF資料下載
參數資料
| 型號： | CYV15G0204RB |
| 廠商： | Cypress Semiconductor Corp. |
| 英文描述： | Independent Clock Dual HOTLink II⑩ Reclocking Deserializer |
| 中文描述： | 獨立時鐘雙的HOTLink二⑩時鐘重計解串器 |
| 文件頁數： | 14/24頁 |
| 文件大?。?/td> | 332K |
| 代理商： | CYV15G0204RB |
CYV15G0204RB
Document #: 38-02103 Rev. *C
Page 14 of 24
Device Configuration Strategy
The following is a series of ordered events needed to load the
configuration latches on a per channel basis:
1. Pulse RESET Low after device power-up. This operation
resets both channels. Initialize the JTAG state machine to
its reset state as detailed in
JTAG Support
.
2. Set the static latch banks for the target channel. [Optional
step if the default settings match the desired configuration.]
3. Set the dynamic bank of latches for the target channel.
Enable the Receive PLLs and set each channel for SMPTE
data reception (RXBISTx[1:0] = 01) or BIST data reception
(RXBISTx[1:0] = 10). [Required step]
JTAG Support
The CYV15G0204RB contains a JTAG port to allow system
level diagnosis of device interconnect. Of the available JTAG
modes, boundary scan, and bypass are supported. This
capability is present only on the LVTTL inputs and outputs and
the TRGCLKx± clock input. The high-speed serial inputs and
outputs are not part of the JTAG test chain.
To ensure valid device operation after power-up (including
non-JTAG operation), the JTAG state machine should also be
initialized to a reset state. This should be done in addition to
the device reset (using RESET). The JTAG state machine can
be initialized using TRST (asserting it LOW and de-asserting
it or leaving it asserted), or by asserting TMS HIGH for at least
5 consecutive TCLK cycles. This is necessary in order to
ensure that the JTAG controller does not enter any of the test
modes after device power-up. In this JTAG reset state, the rest
of the device will be in normal operation.
Note
. The order of device reset (using RESET) and JTAG
initialization does not matter.
3-Level Select Inputs
Each 3-Level select inputs reports as two bits in the scan
register. These bits report the LOW, MID, and HIGH state of
the associated input as 00, 10, and 11 respectively
JTAG ID
The JTAG device ID for the CYV15G0204RB is ‘0C811069’x.
Table 4. Device Control Latch Configuration Table
ADDR
Channel
Type
DATA6
DATA5
DATA4
DATA3
DATA2
DATA1
DATA0
Reset
Value
0
(000b)
A
S
1
0
X
X
0
0
RXRATEA
101111
1
(001b)
A
S
SDASEL2A[1]
SDASEL2A[0]
SDASEL1A[1]
SDASEL1A[0]
X
X
TRGRATEA
101011
2
(010b)
A
D
RXBISTA[1]
RXPLLPDA
RXBISTA[0]
X
ROE2A
ROE1A
X
101100
5
(101b)
B
S
1
0
X
X
0
0
RXRATEB
101111
6
(110b)
B
S
SDASEL2B[1]
SDASEL2B[0]
SDASEL1B[1]
SDASEL1B[0]
X
X
TRGRATEB
101011
7
(111b)
B
D
RXBISTB[1]
RXPLLPDB
RXBISTB[0]
X
ROE2B
ROE1B
X
101100
Table 5. Receive BIST Status Bits
{BISTSTx, RXDx[0], RXDx[1]}
Description
Receive BIST Status
(Receive BIST = Enabled)
000, 001
010
011
100
101
BIST Data Compare
. Character compared correctly.
BIST Last Good
. Last Character of BIST sequence detected and valid.
Reserved.
BIST Last Bad
.
Last Character of BIST sequence detected invalid.
BIST Start
. Receive BIST is enabled on this channel, but character compares have not yet
commenced. This also indicates a PLL Out of Lock condition.
BIST Error
. While comparing characters, a mismatch was found in one or more of the character
bits.
BIST Wait
. The receiver is comparing characters. but has not yet found the start of BIST
character to enable the LFSR.
110
111
[+] Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| CYV15G0204RB-BGC | Independent Clock Dual HOTLink II⑩ Reclocking Deserializer |
| CYV15G0204RB-BGXC | Independent Clock Dual HOTLink II⑩ Reclocking Deserializer |
| CYV15G0204TRB | Independent Clock HOTLink II⑩ Dual Serializer and Dual Reclocking Deserializer |
| CYV15G0204TRB-BGC | Independent Clock HOTLink II⑩ Dual Serializer and Dual Reclocking Deserializer |
| CYV15G0204TRB-BGXC | Independent Clock HOTLink II⑩ Dual Serializer and Dual Reclocking Deserializer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CYV15G0204RB_09 | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Independent Clock Dual HOTLink II Reclocking Deserializer |
| CYV15G0204RB-BGC | 功能描述:視頻 IC 2x Indep Reclockers COM RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
| CYV15G0204RB-BGXC | 功能描述:IC DESERIAL HOTLINK 256LBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 串行器，解串行器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 功能:解串器 數據速率:2.5Gbps 輸入類型:串行 輸出類型:并聯 輸入數:- 輸出數:24 電源電壓:1.8 V ~ 3.3 V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP（10x10） 包裝:管件 |
| CYV15G0204TRB | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Independent Clock HOTLink II⑩ Dual Serializer and Dual Reclocking Deserializer |
| CYV15G0204TRB-BGC | 功能描述:視頻 IC 2x Indep Reclocker Serializer COM RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。