- 您現在的位置：買賣IC網 > PDF目錄369678 > CYCLONE08UM MON08 Cyclone Users Manual PDF資料下載
參數資料
| 型號： | CYCLONE08UM |
| 英文描述： | MON08 Cyclone Users Manual |
| 中文描述： | 的MON08氣旋用戶手冊 |
| 文件頁數： | 64/64頁 |
| 文件大?。?/td> | 756K |
| 代理商： | CYCLONE08UM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁當前第64頁
62
MON08 Cyclone User Manual
P&E
Microcomputer
Systems, Inc.
MON08 CYCLONE
PROG08SZ software continually records any changes to these security bytes
and stores them in the file SECURITY.INI. The information in this file is also
shared with P&E's In-Circuit Debugger and In-Circuit Simulator Software.
This allows the user to reset the device and still have access to the monitor
mode.
Sometimes the case comes up where the software can’t pass security mode.
The Target Connection and Security Dialog section has a “STATUS” section
which describes the different failures and what to check in each case.
The most common reasons for not passing security are:
- You are not choosing the proper security code to pass security.
- On a power on reset, the device is not powering down to below 0.1
volts. With a Class I board (ICS with processor), you may be driving
the pins on the emulation header while the device is being powered
down. This back-drives current through the ports and doesn’t let the
device fully power down. On other classes of boards, when prompted
to power down the device, the supply voltage might not be dropping
lower than 0.1v which it must to have a power-on reset.
- Make sure the “Target hardware type” is set to the proper class of
hardware.
There are several ways you can specify the proper security bytes:
- If you know the programmed security bytes, i.e. the bytes from
$FFF6-$FFFD, you can enter them in the edit box listed “User:” and
click OK(Retry).
- You can use the “Load from S19” to specify the s-record file which
contains the object information currently programmed into the MCU.
P&E’s software will automatically extract the security information
from this file and use it to pass security. Once you have specified the
s-record file, click the OK(Retry) button.
- You can erase the device. Run the PROG08SZ application, and when the
above box appears, select the “IGNORE security failure…” option and click
OK. Use the Choose Module command to select the appropriate programming
algorithm, and select Erase Module. This should erase the device. You will
have to execute the Choose Module command again before you can access the
blank device. Note: on some older revisions of silicon, you can’t ignore the
security failure, and it will bring this box back up every time you click
OK(Retry). If this is the case, you should obtain the latest silicon revision from
Motorola.
相關PDF資料 |
PDF描述 |
|---|---|
| CYK001M16SCCAU | Memory |
| CYK001M16ZCCAU | Memory |
| CYK512K16SCCAU | Memory |
| CYL2T0201-AIP | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| CYM1910PV-25C | SYNC SRAM|16KX68|CMOS|DIP|104PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CYCLONEIII VIDEO DEV KIT | 制造商:Altera Corporation 功能描述:CYCLONEIII VIDEO DEV KIT*NIC* |
| CYCLONEMAX | 功能描述:程序設計器 - 基于處理器 CYCLONE MAX FLASH PROGRA RoHS:否 制造商:Olimex Ltd. 產品:Programmers 工具用于評估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口類型:USB 工作電源電壓:1.8 V to 5.5 V |
| CYCLONEMAX | 制造商:Freescale Semiconductor 功能描述:Stand-alone in-circuit programmer/debugg |
| CYD01S18V | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:FLEx18⑩ 3.3V 64K/128K/256K/512K x 18 Synchronous Dual-Port RAM |
| CYD01S18V-133BBC | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:FLEx18⑩ 3.3V 64K/128K/256K/512K x 18 Synchronous Dual-Port RAM |
發布緊急采購，3分鐘左右您將得到回復。