- 您現在的位置：買賣IC網 > PDF目錄369678 > CYCLONE08UM MON08 Cyclone Users Manual PDF資料下載
參數資料
| 型號： | CYCLONE08UM |
| 英文描述： | MON08 Cyclone Users Manual |
| 中文描述： | 的MON08氣旋用戶手冊 |
| 文件頁數： | 58/64頁 |
| 文件大小： | 756K |
| 代理商： | CYCLONE08UM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁當前第58頁第59頁第60頁第61頁第62頁第63頁第64頁
56
MON08 Cyclone User Manual
P&E
Microcomputer
Systems, Inc.
MON08 CYCLONE
button, the software can use this to gain control of the target system. If this
option is checked, the software will prompt the user to push the target reset
button when a reset of the target system is desired. If the option is unchecked,
the software will ask the user to power cycle the target system to achieve a
reset.
MON08 Cable connection communications type (Class II boards Only)
This selection box is valid only for Class II hardware configurations using the
MON08 cable. It allows the user to specify the sequence that the software uses
to power up the ICS system. When the software tries to create a power-on reset
condition, two events must occur:
1. Power of the target MCU must go below 0.1v. This means that the
processor can not be receiving power from its power pins, nor can it have a
significant voltage being driven on port pins or the IRQ line, as these will
drive the MCU power back through these pins. It is crucial, therefore, to
have the ICS and the Target both powered down at some point in time.
2. The processor MON08 configuration pins, including IRQ, must be
properly driven when the target processor resets to drive it into monitor
mode. If these pins are not set up properly before the processor powers up,
the processor may start up in user mode.
PowerDown ICS, Ask the user to power down their board, PowerUp ICS,
Ask the user to power up their board
This is the default option and should work for most, if not all, ICS08/Target
Board solutions. Refer to the manual addendum under startup for the settings
for a specific ICS board. It requires the user go through two dialog stages, and
requires more time than simply cycling the power.
1. Software automatically powers down the ICS.
2. Software Asks the user to power down the board as follows:
Figure 6-24: Power Down Dialog
3. Software automatically powers up the ICS, which configures the
processor’s MON08 configuration pins.
相關PDF資料 |
PDF描述 |
|---|---|
| CYK001M16SCCAU | Memory |
| CYK001M16ZCCAU | Memory |
| CYK512K16SCCAU | Memory |
| CYL2T0201-AIP | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| CYM1910PV-25C | SYNC SRAM|16KX68|CMOS|DIP|104PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CYCLONEIII VIDEO DEV KIT | 制造商:Altera Corporation 功能描述:CYCLONEIII VIDEO DEV KIT*NIC* |
| CYCLONEMAX | 功能描述:程序設計器 - 基于處理器 CYCLONE MAX FLASH PROGRA RoHS:否 制造商:Olimex Ltd. 產品:Programmers 工具用于評估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口類型:USB 工作電源電壓:1.8 V to 5.5 V |
| CYCLONEMAX | 制造商:Freescale Semiconductor 功能描述:Stand-alone in-circuit programmer/debugg |
| CYD01S18V | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:FLEx18⑩ 3.3V 64K/128K/256K/512K x 18 Synchronous Dual-Port RAM |
| CYD01S18V-133BBC | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:FLEx18⑩ 3.3V 64K/128K/256K/512K x 18 Synchronous Dual-Port RAM |
發布緊急采購，3分鐘左右您將得到回復。