- 您現在的位置：買賣IC網 > PDF目錄369678 > CYCLONE08UM MON08 Cyclone Users Manual PDF資料下載
參數資料
| 型號： | CYCLONE08UM |
| 英文描述： | MON08 Cyclone Users Manual |
| 中文描述： | 的MON08氣旋用戶手冊 |
| 文件頁數： | 57/64頁 |
| 文件大?。?/td> | 756K |
| 代理商： | CYCLONE08UM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁當前第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
MON08 Cyclone User Manual
55
P&E
Microcomputer
Systems, Inc.
MON08 CYCLONE
6.3.1.3
Advanced Settings Dialog
The Advanced Button brings up a dialog which allows the user to set specific
protocol settings. The following is an explanation of each part of the advanced
settings dialog.
Figure 6-23: Target Hardware Type: Advanced Settings Dialog
Tpd and Tpu Timing
These timing parameters are mostly designed for Class I boards, although the
delays are valid for all classes of boards. Many of the ICS boards and user
target boards need time to power down and power up.
Whenever power is automatically switched off, or is manually requested to be
switched off, the software waits for an amount of time equal to the Tpd delay
time before proceeding to the connection protocol. This is because a board or
power supply may have capacitance which holds the power up for a short time
after the supply has been switched off, but the supply voltage must reach less
than 0.1v before it is turned back on if a Power-On reset is to occur.
Whenever power is automatically switched on, or is manually requested to be
switched on, the software waits for an amount of time equal to the Tpu delay
time before attempting to contact the 68HC08 processor. This is to allow time
not only for power to be fully available, but to wait until any reset driver has
finally released the RESET line. On many ICS08 boards (such as the
ICS08RK, M68ICS08JL3, M68ICS08JLJK, and ICS08GP20) the Tpu can be
decreased to as little as 250ms with no adverse effects.
Target has RESET button (class III boards only):
The software
occasionally needs to get control of the target. On systems which are Class III
boards with the monitor mode circuitry built-in (including RS-232 driver),
there is no means to reset the target to gain control. If the board has a reset
相關PDF資料 |
PDF描述 |
|---|---|
| CYK001M16SCCAU | Memory |
| CYK001M16ZCCAU | Memory |
| CYK512K16SCCAU | Memory |
| CYL2T0201-AIP | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| CYM1910PV-25C | SYNC SRAM|16KX68|CMOS|DIP|104PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CYCLONEIII VIDEO DEV KIT | 制造商:Altera Corporation 功能描述:CYCLONEIII VIDEO DEV KIT*NIC* |
| CYCLONEMAX | 功能描述:程序設計器 - 基于處理器 CYCLONE MAX FLASH PROGRA RoHS:否 制造商:Olimex Ltd. 產品:Programmers 工具用于評估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口類型:USB 工作電源電壓:1.8 V to 5.5 V |
| CYCLONEMAX | 制造商:Freescale Semiconductor 功能描述:Stand-alone in-circuit programmer/debugg |
| CYD01S18V | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:FLEx18⑩ 3.3V 64K/128K/256K/512K x 18 Synchronous Dual-Port RAM |
| CYD01S18V-133BBC | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:FLEx18⑩ 3.3V 64K/128K/256K/512K x 18 Synchronous Dual-Port RAM |
發布緊急采購，3分鐘左右您將得到回復。