參數資料
型號： CS5460A-BS
廠商： CIRRUS LOGIC INC
元件分類： ADC
英文描述： Single Phase Bi-Directional Power/Energy IC
中文描述： 2-CH 24-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO24
封裝： MO-150, SSOP-24
文件頁數： 33/54頁
文件大小： 876K
代理商： CS5460A-BS
CS5460A
33
The
surge-current limits of 100 mA. This applies to brief
voltage/current spikes (<250 ms). The limit is
10 mA for DC input overload situations. To prevent
permanent damage to the CS5460A, the designer
must include adequate protection circuitry in the
power meter design, to insure that these pin cur-
rent limits are never exceeded, when CS5460A is
operating in the intended power-line metering envi-
ronment.
Focusing specifically on Figure 7, which shows
how voltage/current transformers can be used to
sense the line-voltage/line-current, suppose for ex-
ample that the requirements for a certain 120 VAC
power system require that the power meter must
be able to withstand up to a 8 kV voltage spike on
the power line during normal operating conditions.
To provide a suitable sensor voltage input level to
the voltage channel input pins of the CS5460A, the
turns ratio of the voltage-sense transformer should
be chosen such that the ratio is, for example, on
the order of 1000:1. A voltage-sense transformer
with a 1000:1 turns ratio will provide a 120 mV
(rms) signal to the CS5460A’s differential voltage
channel inputs, when the power line voltage is at
the nominal level of 120 VAC. Therefore, a brief
8 kV surge would be reduced to a 8 V surge across
R
V+
.
What happens when 8 volts (common-mode) is
present across one of the analog input pins of the
CS5460A The Vin+/Vin- and Iin+/Iin- pins of the
CS5460A are equipped with internal protection di-
odes. If a voltage is presented to any of these pins
that is larger than approximately 7 V (with respect
to VA- pin) these protection diodes will turn on in-
side the CS5460A. But in order to prevent exces-
sive current levels from flowing through the device,
the value of R
V+
must be large enough that when a
8V surge is present across the secondaries of the
voltage-sense transformer, the brief surge current
through R
V+
should not be any greater than
100 mA. Therefore, a minimum value for R
V+
would be (8 V - 7 V) / 100 mA = 10
. This value
may be increased as needed, to easily obtain the
desired cutoff frequency of the anti-aliasing filter on
the voltage channel (described later), and also to
provide some margin. But the designer should try
voltage/current-channel
inputs
have
to avoid using values for the protection resistors
that are excessively high. A typical value for R
V+
would be 470
.
The VIN- pin should also have a protection resistor
(called R
V-
in Figure 7). To maintain symmetry, the
value of R
V-
should be made equal to R
V+
.
For the current channel inputs (Iin+ and Iin-), if the
maximum current rating (I
max
) for this power line is
30 A (RMS), then a suitable turns ratio for the cur-
rent-sense transformer might be 200:1. Since the
maximum load for a 120 VAC line rated at 30 A
would be 4
(for unity power factor), a brief 8 kV
surge across “L” and “N” could generate as much
as 2000 A (RMS) of current through the primaries
of the current-sense transformer. This can in turn
generate as much as 10 V across the secondaries
of the current-sense transformer. This voltage is
high enough to turn on one or more of the internal
protection diodes located off of the Iin+/Iin- pins.
Therefore, the value of the protection resistor that
will limit the current flow to less than 100 mA would
be (10 V - 7 V) / 100 mA = 30
. In order to pro-
vide some margin and to use the same resistor val-
ues that are used on the Vin+/Vin- pins, a 470
resistor can be used as a lower limit for the R
I+
and
R
I-
resistors shown in Figure 7.
Referring to the circuit implementations shown in
Figures 6, 8, and 9, note that when resistor-divider
configurations are used to provide the voltage
channel sense voltage, the VIN+ pin does not need
an additional, separate, dedicated protection resis-
tor. This is because the resistive voltage-divider al-
ready provides the series resistance that is needed
for this protection resistance (from R
1
and R
2
).
(And note in Figure 8 that this is true for both the
VIN+ pin and the VIN- pin.) In Figure 7, a voltage
transformer is used as the voltage sensor. When
any type of transformer is used as the sensor de-
vice for voltage (or current) channel, a dedicated
protection resistor R
V+
should be installed in series
with the VIN+ pin, and similarly, a resistor (R
V-
)
should be installed in series to the VIN- input pin.
Additional considerations/techniques regarding
the protection of the analog input pins against sud-
den high-frequency, high-level voltage/current
surges are discussed in Section 3.14.
相關PDF資料
PDF描述
CS5460A Single Phase Bi-Directional Power/Energy IC
CS5460 Single Phase Bi-Directional Power/Energy IC(單相雙向功率/能量IC)
CS5461A-IS Single Phase, Bi-directional Power/Energy IC
CS5461A-ISZ Single Phase, Bi-directional Power/Energy IC
CS5461A Single Phase, Bi-directional Power/Energy IC
相關代理商/技術參數
參數描述
CS5460A-BSZ 功能描述:電流和電力監控器、調節器 Single-Phase Bi-Dir Power/Energy IC RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel
CS5460A-BSZ 制造商:Cirrus Logic 功能描述:Driver IC 制造商:Cirrus Logic 功能描述:IC ENERGY METERING 1PHASE 24SSOP 制造商:Cirrus Logic 功能描述:IC, ENERGY METERING, 1PHASE, 24SSOP
CS5460A-BSZR 功能描述:電流和電力監控器、調節器 IC Sngl-Phs BiDirect PWR/Energy RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel
CS5460-BS 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Cirrus Logic 功能描述:
CS5460C-ISZ 功能描述:電流和電力監控器、調節器 Sngl-Phs Bi-Drctnl Power/Energy RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*