- 您現在的位置：買賣IC網 > PDF目錄380082 > CS5460A-BS (CIRRUS LOGIC INC) Single Phase Bi-Directional Power/Energy IC PDF資料下載
參數資料
| 型號： | CS5460A-BS |
| 廠商： | CIRRUS LOGIC INC |
| 元件分類： | ADC |
| 英文描述： | Single Phase Bi-Directional Power/Energy IC |
| 中文描述： | 2-CH 24-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO24 |
| 封裝： | MO-150, SSOP-24 |
| 文件頁數： | 21/54頁 |
| 文件大?。?/td> | 876K |
| 代理商： | CS5460A-BS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
CS5460A
21
3. FUNCTIONAL DESCRIPTION
3.1 Pulse-Rate Output
As an alternative to reading the real energy
through the serial port, the EOUT and EDIR pins
provide a simple interface with which signed ener-
gy can be accumulated. Each EOUT pulse repre-
sents a predetermined quantity of energy. The
quantity of energy represented in one pulse can be
varied by adjusting the value in the Pulse-Rate
Register. Corresponding pulses on the EDIR out-
put pin signify that the sign of the energy is nega-
tive. Note that these pulses are not influenced by
the value of the Cycle-Count Register, and they
have no reliance on the computation cycle, de-
scribed earlier. With MCLK = 4.096 MHz, K = 1,
the pulses will have an average frequency (in Hz)
equal to the frequency setting in the Pulse Rate
Register when the input signals into the voltage
and current channels cause full-scale readings in
the Instantaneous Voltage and Current Registers.
When MCLK/K is not equal to 4.096 MHz, the
pulse-rate should be scaled by a factor of
4.096 MHz / (MCLK/K) to get the actual output
pulse-rate.
EXAMPLE #1:
For a power line with maximum rat-
ed levels of 250 V (RMS) and 20 A (RMS), the
pulse-frequency on the EOUT pin needs to be
‘IR’ = 100 pulses-per-second (100 Hz) when the
RMS-voltage and RMS-current levels on the power
line are 220 V and 15 A respectively. To meet this
requirement, the pulse-rate frequency (‘PR’) in the
Pulse-Rate Register must be set accordingly.
After calibration, the first step to finding the value
of ‘PR’ is to set the voltage and current sensor gain
constants, K
V
and K
I
, such that there will be ac-
ceptable voltage levels on the CS5460A inputs
when the power line voltage and current levels are
at the maximum values of 250 V and 20 A. K
V
and
K
I
are needed to determine the appropriate ratios
of the voltage/current transformers and/or shunt
resistor values to use in the front-end voltage/cur-
rent sensor networks.
For a sinewave, the largest RMS value that can be
accurately measured (without over-driving the in-
puts) will register ~0.7071 of the maximum DC in-
put level. Since power signals are often not
perfectly sinusoidal in real-world situations, and to
provide for some over-range capability, the RMS
Voltage Register and RMS Current Register is set
to measure 0.6 when the RMS-values of the
line-voltage and line-current levels are 250 V and
20 A. Therefore, when the RMS registers measure
0.6, the voltage level at the inputs will be
0.6 x 250 mV = 150 mV. The sensor gain con-
stants, K
V
and K
I
, are determined by demanding
that the voltage and current channel inputs should
be 150 mV RMS when the power line voltage and
current are at the maximum values of 250 V and
20 A.
K
V
= 150 mV / 250 V = 0.0006
K
I
= 150 mV / 20 A = 0.0075
These sensor gain constants are used to calculate
what the input voltage levels will be on the
CS5460A inputs when the line-voltage and
line-current are 220 V and 15 A. These values are
V
Vnom
and V
Inom.
V
Vnom
= K
V
* 220 V = 132 mV
V
Inom
= K
I
* 15 A = 112.5 mV
The pulse rate on EOUT will be at ‘PR’ pulses per
second (Hz) when the RMS-levels of voltage/cur-
rent inputs are at 250 mV. When the voltage/cur-
rent inputs are set at V
Vnom
and V
Inom
, the pulse
rate needs to be ‘IR’ = 100 pulses per second. IR
will be some percentage of PR. The percentage is
defined by the ratios of V
Vnom
/250 mV and
V
Inom
/250 mV with the following formula:
From this equation the value of ‘PR’ is shown as:.
Therefore the Pulse-Rate Register is set to
~420.875 Hz, or 0x00349C.
The above equation is valid when current channel
is set to x10 gain. If current channel gain is set to
x50, then the equation becomes:
PulseRate
IR
PR
V
250mV
-------------------
V
250mV
-------------------
=
=
PR
250mV
------------------
V
250mV
------------------
×
-V
250mV
132mV
250mV
112.5mV
×
----------------100Hz
=
=
PR
250mV
------------------
V
50mV
---------------
×
V
=
相關PDF資料 |
PDF描述 |
|---|---|
| CS5460A | Single Phase Bi-Directional Power/Energy IC |
| CS5460 | Single Phase Bi-Directional Power/Energy IC(單相雙向功率/能量IC) |
| CS5461A-IS | Single Phase, Bi-directional Power/Energy IC |
| CS5461A-ISZ | Single Phase, Bi-directional Power/Energy IC |
| CS5461A | Single Phase, Bi-directional Power/Energy IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS5460A-BSZ | 功能描述:電流和電力監控器、調節器 Single-Phase Bi-Dir Power/Energy IC RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel |
| CS5460A-BSZ | 制造商:Cirrus Logic 功能描述:Driver IC 制造商:Cirrus Logic 功能描述:IC ENERGY METERING 1PHASE 24SSOP 制造商:Cirrus Logic 功能描述:IC, ENERGY METERING, 1PHASE, 24SSOP |
| CS5460A-BSZR | 功能描述:電流和電力監控器、調節器 IC Sngl-Phs BiDirect PWR/Energy RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel |
| CS5460-BS | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Cirrus Logic 功能描述: |
| CS5460C-ISZ | 功能描述:電流和電力監控器、調節器 Sngl-Phs Bi-Drctnl Power/Energy RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。