- 您現在的位置：買賣IC網 > PDF目錄169489 > CAP1014-1-EZK (STANDARD MICROSYSTEMS CORP) SPECIALTY ANALOG CIRCUIT, QCC32 PDF資料下載
參數資料
| 型號： | CAP1014-1-EZK |
| 廠商： | STANDARD MICROSYSTEMS CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 封裝： | 5 X 5 MM, 0.50 MM PITCH, ROHS COMPLIANT, QFN-32 |
| 文件頁數： | 8/73頁 |
| 文件大?。?/td> | 945K |
| 代理商： | CAP1014-1-EZK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁
Multiple Channel Capacitive Touch Sensor and LED Driver
Datasheet
Revision 1.64 (01-15-09)
16
SMSC CAP1014
DATASHEET
The Host will NACK (not acknowledge) the last data byte to be received from the client by holding the
SMBus data line high after the 8th data bit has been sent. For the Block Read protocol, the Host will
ACK each data byte that it receives except the last data byte.
3.1.5
SMBus Stop Bit
The SMBus Stop bit is defined as a transition of the SMBus Data line from a logic ‘0’ state to a logic
‘1’ state while the SMBus clock line is in a logic ‘1’ state. When the CAP1014 detects an SMBus Stop
bit, and it has been communicating with the SMBus protocol, it will reset its client interface and prepare
to receive further communications.
3.1.6
SMBus Time-out
The CAP1014 includes an SMBus time-out feature. Following a 30ms period of inactivity on the SMBus
where the SMCLK pin is held low, the device will time-out and reset the SMBus interface.
The time-out function defaults to disabled. It can be enabled by setting the TIMEOUT bit in the
Configuration register (see Section 5.13).
3.1.7
SMBus and I2C Compliance
The major difference between SMBus and I2C devices is highlighted here. For complete compliance
information refer to the SMBus 2.0 specification.
1. Minimum frequency for SMBus communications is 10kHz.
2. The client protocol will reset if the clock is held low longer than 30ms.
3. The client protocol will reset if both the clock and the data line are high for longer than 150us (idle
condition).
4. I2C devices do not support the Alert Response Address functionality (which is optional for SMBus).
3.2
SMBus Protocols
The CAP1014 is SMBus 2.0 compatible and supports Send Byte, Read Byte, Block Read, Receive
Byte as valid protocols as shown below. The CAP1014 also supports the I2C block read and block
write protocols. Finally, it will respond to the Alert Response Address protocol but is not in full
compliance.
All of the below protocols use the convention in Table 3.1.
Table 3.1 Protocol Format
DATA SENT
TO DEVICE
DATA SENT TO
THE HOST
Data sent
相關PDF資料 |
PDF描述 |
|---|---|
| CAT1021LI-42TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| CAT1023LE-28TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| CAT1021LE-45TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| CAT1023LI-28TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| CAT1023LE-45TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAP1014-1-EZK-TR | 制造商:SMSC 制造商全稱:SMSC 功能描述:Multiple Channel Capacitive Touch Sensor and LED Driver |
| CAP1014-2-EZK-TR | 制造商:SMSC 制造商全稱:SMSC 功能描述:Multiple Channel Capacitive Touch Sensor and LED Driver |
| CAP1026 | 制造商:SMSC 制造商全稱:SMSC 功能描述:6 Channel Capacitive Touch Sensor with 2 LED Drivers |
| CAP1026-1-AP-TR | 制造商:SMSC 制造商全稱:SMSC 功能描述:6 Channel Capacitive Touch Sensor with 2 LED Drivers |
| CAP1028 | 制造商:SMSC 制造商全稱:SMSC 功能描述:8 Channel Capacitive Touch Sensor with 2 LED Drivers |
發布緊急采購，3分鐘左右您將得到回復。