- 您現在的位置：買賣IC網 > PDF目錄169489 > CAP1014-1-EZK (STANDARD MICROSYSTEMS CORP) SPECIALTY ANALOG CIRCUIT, QCC32 PDF資料下載
參數資料
| 型號： | CAP1014-1-EZK |
| 廠商： | STANDARD MICROSYSTEMS CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 封裝： | 5 X 5 MM, 0.50 MM PITCH, ROHS COMPLIANT, QFN-32 |
| 文件頁數： | 15/73頁 |
| 文件大?。?/td> | 945K |
| 代理商： | CAP1014-1-EZK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁
Multiple Channel Capacitive Touch Sensor and LED Driver
Datasheet
Revision 1.64 (01-15-09)
22
SMSC CAP1014
DATASHEET
4.2
RESET Pin
The RESET pin is an active high reset that is driven from an external source. While it is asserted high,
all the internal blocks will be held in reset including the SMBus. All configuration settings will be reset
to default states and all readings will be cleared. Once the RESET pin is pulled low, the CAP1014 will
begin operation as if a power-on-reset had occurred.
4.3
LED Drivers
The CAP1014 contains eleven (11) LED Drivers. Each LED Driver is controlled independently of the
others and may be linked to the corresponding Capacitive Touch Sensor inputs. In addition, LED
drivers 1 - 8 can be configured to operate in one of the following modes with either push-pull or open-
drain drive. LED drivers 9 - 11 will only operate in as an open-drain driver.
1. Direct - The LED is configured to be on or off when the corresponding button is pressed or not
pressed. The dimness of both “on” states and “off” states can be programmed as well as the rising
and falling ramp times and delay when the corresponding button is released
2. Breathe - The LED is configured to breathe. Over the course of the programmed cycle the LED
will transition from the programmed minimum to the programmed maximum and then back off
again. This mode operates independently of any stimuli or may be linked so that the LED breathes
when the stimuli is asserted (or deasserted). This feature is commonly used for power LEDs when
in standby mode.
3. Pulse - The LED is configured to breathe 5 times with a programmable rate and dimness controls.
This mode is linked to a button press detection or release.
LED11 operates differently than the other LED outputs in three ways. First, it is configured to drive up
to two external LED channels simultaneously. Second, it is not disabled during the Sleep or Deep
Sleep modes of operation (see Section 5.1) and allows for different behaviors when the device is in
Fully Active Mode versus when the device is in Sleep or Deep Sleep mode.
4.3.1
Linking LEDs to Capacitive Touch Sensors
LEDs 1 - 7 can be optionally linked to Capacitive Touch Sensors 1-7 so that when the sensor detects
a button press, the corresponding LED will be actuated at one of the programmed responses.
4.4
Capacitive Touch Sensing
The CAP1014 contains 14 independent Capacitive Touch Sensor inputs. Each sensor has dynamic
range to detect a a change of capacitance due to a touch. Additionally, each sensor can be configured
to be automatically and routinely re-calibrated.
4.4.1
Multiple Button Presses
If multiple sensor buttons (with a programmable threshold - see Section 5.22) are simultaneously
detected, then only the first N buttons that are detected are flagged. All other buttons are ignored.
Furthermore, the device remembers which buttons were legitimate so new touches are not detected
so long as N buttons are pressed.
Likewise, if too many (based on the programmed threshold - see Section 5.22) grouped sensor
presses are detected, then the device will block all press detections on the grouped buttons and cancel
any current presses as if the sensor had been released.
4.4.2
Grouped Sensors
Capacitive Touch Sensors 8 through 14 inclusive are automatically grouped as a single entity. Each
sensor is sampled independently, however for purposes of activation, recalibration, and repeat rates,
相關PDF資料 |
PDF描述 |
|---|---|
| CAT1021LI-42TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| CAT1023LE-28TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| CAT1021LE-45TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| CAT1023LI-28TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| CAT1023LE-45TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAP1014-1-EZK-TR | 制造商:SMSC 制造商全稱:SMSC 功能描述:Multiple Channel Capacitive Touch Sensor and LED Driver |
| CAP1014-2-EZK-TR | 制造商:SMSC 制造商全稱:SMSC 功能描述:Multiple Channel Capacitive Touch Sensor and LED Driver |
| CAP1026 | 制造商:SMSC 制造商全稱:SMSC 功能描述:6 Channel Capacitive Touch Sensor with 2 LED Drivers |
| CAP1026-1-AP-TR | 制造商:SMSC 制造商全稱:SMSC 功能描述:6 Channel Capacitive Touch Sensor with 2 LED Drivers |
| CAP1028 | 制造商:SMSC 制造商全稱:SMSC 功能描述:8 Channel Capacitive Touch Sensor with 2 LED Drivers |
發布緊急采購，3分鐘左右您將得到回復。