參數資料
型號： CAP1014-1-EZK
廠商： STANDARD MICROSYSTEMS CORP
元件分類： 模擬信號調理
英文描述： SPECIALTY ANALOG CIRCUIT, QCC32
封裝： 5 X 5 MM, 0.50 MM PITCH, ROHS COMPLIANT, QFN-32
文件頁數： 17/73頁
文件大?。?/td> 945K
代理商： CAP1014-1-EZK
Multiple Channel Capacitive Touch Sensor and LED Driver
Datasheet
Revision 1.64 (01-15-09)
24
SMSC CAP1014
DATASHEET
Slides in either direction are configured to flag an interrupt and to cause an LED to be actuated
(separate for each direction). The Slide is detected independently of a Press and Hold or a Tap
condition and only one condition may be present at any one time.
So long as a slide is maintained in either direction, it will flag an interrupt at the programmed repeat
rate (as determined by the RPT_RATE_SL bit settings). If the slide is removed or changes direction,
then it will reset and return to normal operation.
4.5.4
Relative Position
The CAP1014 has the option to indicate the relative position of a touch on the Grouped sensors. This
value is stored either as a scaled number from 2 to 98 indicating where a tap, press and hold, or the
end of a slide was detected or as a 8-bit number that represents volumetric data. When configured to
store volumetric data, the user may write a base setting at any time that is modified based on Grouped
sensor behavior (see Section 5.4).
4.5.5
Slider Velocity
The repeat rate can be dynamically increased based on the speed of a slide. This permits slow sliding
motions to have precise, step-by-step volume control and faster motions to generate increasingly fast
volume changes.
Two techniques are employed to make increase the number of interrupts generated based on speed.
First, the slide speed is measured and the repeat rate is increased to provide more interrupts for the
same distance traveled relative to a slower slide. Second, additional interrupts are generated
immediately after the slide ends to further increase the change in volume. The number of additional
interrupts is based on slide speed; both of these dynamic slider behaviors are controlled by the Slider
Velocity Register.
4.6
ALERT Pin
The ALERT pin is an active high output that is driven high when an interrupt event is detected. It is
also used to wake the device from Deep Sleep mode.
Whenever an interrupt is generated, the INT bit (see Section 5.1) is set. The ALERT pin is cleared
when INT bit is cleared by the user. Additionally, when the INT bit is cleared by the user status bits
are cleared only if no press is detected.
4.6.1
Button Interrupt Behavior
For non-grouped buttons, an interrupt is generated when a touch is detected. If the repeat rate is
enabled (see Section 5.13), then, so long as the touch is held, another interrupt will be generated
based on the programmed repeat rate (see Figure 4.2). An interrupt will be generated whenever a
release is detected (see Figure 4.3).
4.6.2
Grouped Sensor Interrupt Behavior
For grouped sensors, an interrupt is generated upon initial detection of a a tap, slide, or press and
hold event. Then, subsequent interrupts are generated as follows:
1. For a slide event, an interrupt is generated based on the programmed repeat rate as well as the
velocity of the slide operation. See Figure 4.6 and Figure 4.7. Additionally, additional interrupts are
generated after the slide has finished. These extra interrupts are generated every round robin cycle
(~35ms) and the number is determined by the speed of the slide.
2. For a tap event there are no further interrupts. See Figure 4.4.
3. For a press and hold event, interrupts are generated based on the programmed repeat rate. If the
repeat rate is disabled, then no further interrupts are generated. See Figure 4.5.
相關PDF資料
PDF描述
CAT1021LI-42TE13 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8
CAT1023LE-28TE13 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8
CAT1021LE-45TE13 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8
CAT1023LI-28TE13 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8
CAT1023LE-45TE13 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8
相關代理商/技術參數
參數描述
CAP1014-1-EZK-TR 制造商:SMSC 制造商全稱:SMSC 功能描述:Multiple Channel Capacitive Touch Sensor and LED Driver
CAP1014-2-EZK-TR 制造商:SMSC 制造商全稱:SMSC 功能描述:Multiple Channel Capacitive Touch Sensor and LED Driver
CAP1026 制造商:SMSC 制造商全稱:SMSC 功能描述:6 Channel Capacitive Touch Sensor with 2 LED Drivers
CAP1026-1-AP-TR 制造商:SMSC 制造商全稱:SMSC 功能描述:6 Channel Capacitive Touch Sensor with 2 LED Drivers
CAP1028 制造商:SMSC 制造商全稱:SMSC 功能描述:8 Channel Capacitive Touch Sensor with 2 LED Drivers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*