參數資料
型號： ATTINY43U-SUR
廠商： Atmel
文件頁數： 84/158頁
文件大小： 0K
描述： MCU AVR 4KB FLASH 8MHZ 20SOIC
產品培訓模塊： tinyAVR Introduction
標準包裝： 1,000
系列： AVR® ATtiny
核心處理器： AVR
芯體尺寸： 8-位
速度： 8MHz
連通性： USI
外圍設備： 欠壓檢測/復位，POR，PWM，溫度傳感器，WDT
輸入/輸出數： 16
程序存儲器容量： 4KB（2K x 16）
程序存儲器類型： 閃存
EEPROM 大小： 64 x 8
RAM 容量： 256 x 8
電壓 - 電源 (Vcc/Vdd)： 1.8 V ~ 5.5 V
數據轉換器： A/D 4x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 20-SOIC（0.295"，7.50mm 寬）
包裝： 帶卷 (TR)
其它名稱： ATTINY43U-SUR-ND
31
8048C–AVR–02/12
ATtiny43U
Idle mode enables the MCU to wake up from external triggered interrupts as well as internal
ones like the Timer Overflow. If wake-up from the Analog Comparator interrupt is not required,
the Analog Comparator can be powered down by setting the ACD bit in the “ACSR – Analog
Comparator Control and Status Register” on page 115. This will reduce power consumption in
Idle mode. If the ADC is enabled, a conversion starts automatically when this mode is entered.
7.1.2
ADC Noise Reduction Mode
When the SM[1:0] bits are written to 01, the SLEEP instruction makes the MCU enter ADC
Noise Reduction mode, stopping the CPU but allowing the ADC, the external interrupts, and the
Watchdog to continue operating (if enabled). This sleep mode halts clk
I/O, clkCPU, and clkFLASH,
while allowing the other clocks to run.
This improves the noise environment for the ADC, enabling higher resolution measurements. If
the ADC is enabled, a conversion starts automatically when this mode is entered. Apart form the
ADC Conversion Complete interrupt, only an External Reset, a Watchdog Reset, a Brown-out
Reset, an SPM/EEPROM ready interrupt, an external level interrupt on INT0 or a pin change
interrupt can wake up the MCU from ADC Noise Reduction mode.
7.1.3
Power-Down Mode
When the SM[1:0] bits are written to 10, the SLEEP instruction makes the MCU enter Power-
down mode. In this mode, the Oscillator is stopped, while the external interrupts, and the Watch-
dog continue operating (if enabled). Only an External Reset, a Watchdog Reset, a Brown-out
Reset, an external level interrupt on INT0, or a pin change interrupt can wake up the MCU. This
sleep mode halts all generated clocks, allowing operation of asynchronous modules only.
7.2
Software BOD Disable
When the Brown-out Detector (BOD) is enabled by BODLEVEL fuses (see Table 19.2 on page
142), the BOD is actively monitoring the power supply voltage during a sleep period. To save
power, it is possible for software to disable the BOD in Power-Down Mode (see “Power-Down
Mode” on page 31). The sleep mode power consumption will then be at the same level as when
BOD is globally disabled by fuses. If disabled by software, the BOD is turned off immediately
after entering the sleep mode and automatically turned on upon wake-up. This ensures safe
operation in case the V
CC level has dropped during the sleep period.
When the BOD has been disabled the wake-up time from sleep mode will be the same as the
wake-up time from RESET. This is in order to ensure the BOD is working correctly before the
MCU continues executing code.
BOD disable is controlled by bit 7 (BODS — BOD Sleep) of MCU Control Register, see “MCUCR
– MCU Control Register” on page 33. Writing this bit to one turns off the BOD in Power-Down
Mode, while a zero in this bit keeps BOD active. The default setting is zero, i.e. BOD active.
Writing to the BODS bit is controlled by a timed sequence and an enable bit, see “MCUCR –
7.3
Power Reduction Register
The Power Reduction Register (PRR), see “PRR – Power Reduction Register” on page 34, pro-
vides a method to stop the clock to individual peripherals to reduce power consumption. The
current state of the peripheral is frozenand the I/O registers can not be read or written.
Resources used by the peripheral when stopping the clock will remain occupied, hence the
相關PDF資料
PDF描述
ATTINY44A-MFR MCU AVR 4KB FLASH 20MHZ 20QFN
ATTINY48-AUR MCU AVR 4KB FLASH 12MHZ 32TQFP
ATTINY48-MMUR MCU AVR 4KB FLASH 12MHZ 28MLF
ATTINY84A-MMHR MCU AVR 8K FLASH 20MHZ 3X3VQFN
ATTINY84V-10SSUR MCU AVR 8KB FLASH 10MHZ 14SOIC
相關代理商/技術參數
參數描述
ATTINY44 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
ATTINY44-15MZ 功能描述:8位微控制器 -MCU 4KB Flash 15MHz Auto 125-degrees C RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY44-15SSZ 功能描述:8位微控制器 -MCU 4KB Flash 15MHz Auto 125-degrees C RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY441-MMH 制造商:Atmel Corporation 功能描述:16MHZ, 3X3MM, 20 VQFN, IND. GRADE, GREEN - Bulk 制造商:Atmel Corporation 功能描述:IC MCU 8BIT 4KB FLASH 20VQFN
ATTINY441-MMHR 制造商:Atmel Corporation 功能描述:16MHZ,3X3MM, 20VQFN, IND.GRADE,GREEN T&R - Tape and Reel 制造商:Atmel Corporation 功能描述:IC MCU 8BIT 4KB FLASH 20VQFN
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*