- 您現在的位置：買賣IC網 > PDF目錄298840 > AT42QT1060-MMU (ATMEL CORP) SPECIALTY ANALOG CIRCUIT, QCC28 PDF資料下載
參數資料
| 型號： | AT42QT1060-MMU |
| 廠商： | ATMEL CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, QCC28 |
| 封裝： | 4 X 4 MM, 1MM HEIGHT, 0.45 MM PITCH, ROHS COMPLIANT, MLF-28 |
| 文件頁數： | 2/32頁 |
| 文件大小： | 389K |
| 代理商： | AT42QT1060-MMU |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
10
9505E–AT42–02/09
AT42QT1060
3.3
LED Traces and Other Switching Signals
Digital switching signals near the sense lines induce transients into the acquired signals,
deteriorating the SNR performance of the device. Such signals should be routed away from the
sensing traces and electrodes, or the design should be such that these lines are not switched
during the course of signal acquisition (bursts).
LED terminals which are multiplexed or switched into a floating state, and which are within, or
physically very near, a key (even if on another nearby PCB) should be bypassed to either Vss or
Vdd with at least a 10 nF capacitor. This is to suppress capacitive coupling effects which can
induce false signal shifts. The bypass capacitor does not need to be next to the LED, in fact it
can be quite distant. The bypass capacitor is noncritical and can be of any type.
LED terminals which are constantly connected to Vss or Vdd do not need further bypassing.
3.4
PCB Cleanliness
All capacitive sensors should be treated as highly sensitive circuits which can be influenced by
stray conductive leakage paths. QT devices have a basic resolution in the femtofarad range; in
this region, there is no such thing as “no clean flux”. Flux absorbs moisture and becomes
conductive between solder joints, causing signal drift and resultant false detections or transient
losses of sensitivity or instability. Conformal coatings trap in existing amounts of moisture which
then become highly temperature sensitive.
The designer should specify ultrasonic cleaning as part of the manufacturing process, and in
cases where a high level of humidity is anticipated, the use of conformal coatings after cleaning
to keep out moisture.
3.5
Power Supply
See Section8.2 on page26 for the power supply range. If the power supply fluctuates slowly
with temperature, the device tracks and compensates for these changes automatically with only
minor changes in sensitivity. If the supply voltage drifts or shifts quickly, the drift compensation
mechanism is not able to keep up, causing sensitivity anomalies or false detections.
The usual power supply considerations with QT parts apply to the device. The power should be
clean and come from a separate regulator if possible. However, this device is designed to
minimize the effects of unstable power, and except in extreme conditions should not require a
separate Low Dropout (LDO) regulator.
See underneath Figure 1-1 on page 4 for suggested regulator manufacturers.
It is assumed that a larger bypass capacitor (like1 F) is somewhere else in the power circuit; for
example, near the regulator.
To assist with transient regulator stability problems, the QT1060 waits 500 s any time it wakes
up from a sleep state (i.e. in SLEEP and LP modes) before acquiring, to allow Vdd to fully
stabilize.
Caution: A regulator IC shared with other logic can result in erratic operation and is
not advised.
A single ceramic 0.1 F bypass capacitor, with short traces, should be placed very
close to the power pins of the IC. Failure to do so can result in device oscillation,
high current consumption, erratic operation etc.
相關PDF資料 |
PDF描述 |
|---|---|
| AT49F010-90TL | 128K X 8 FLASH 5V PROM, 90 ns, PDSO32 |
| AT59C11-10SC-2.7 | Microwire Serial EEPROM |
| AT59C11-10SI | Microwire Serial EEPROM |
| AT59C11-10SI-1.8 | Microwire Serial EEPROM |
| AT59C11-10SI-2.7 | Microwire Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT42QT1060-MMUQS397 | 功能描述:SENSOR IC MTRX TOUCH6KEY 28-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:QTouch™ 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AT42QT1060-MMUR | 功能描述:SENSOR IC MTRX TOUCH6KEY 28-QFN 制造商:microchip technology 系列:QTouch?? 包裝:剪切帶（CT） 零件狀態:在售 類型:按鈕 接近探測:無 輸入數:最高 6 LED 驅動器通道:最高 2 接口:I2C 分辨率:- 電壓 - 電源:1.8 V ~ 5.5 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 封裝/外殼:28-VFQFN 裸露焊盤 供應商器件封裝:28-QFN（4x4） 標準包裝:1 |
| AT42QT1070-MMH | 功能描述:電容觸摸傳感器 QTouch 7 Ch. Touch Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
| AT42QT1070-MMH QS529 | 功能描述:IC TOUCH SENSOR 7KEY 20VQFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:QTouch™ 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AT42QT1070-MMHR |
發布緊急采購，3分鐘左右您將得到回復。