- 您現在的位置：買賣IC網 > PDF目錄366561 > AMMCL00XA (Advanced Micro Devices, Inc.) JT 3C 3#20 SKT RECP PDF資料下載
參數資料
| 型號： | AMMCL00XA |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | JT 3C 3#20 SKT RECP |
| 中文描述： | 2或4兆字節3.0伏，只有Flash微型卡 |
| 文件頁數： | 12/36頁 |
| 文件大?。?/td> | 172K |
| 代理商： | AMMCL00XA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
12
AmMCL00XA
P R E L I M I NA R Y
changed. While in sleep mode, output data is latched
and always available to the system.
Each memory device contains a command register,
which is a latch that saves address, commands, and
data information used by the state machine and
memory array. The state machine is active when V
CC
is
greater than V
LKO
(2.3 - 2.5 V). This is required for valid
program and erase operations.
When Write Enable (WE#) and appropriate CE#
signals are at a logic-low level, and Output Enable
(OE#) is at a logic-high, the command register is
enabled for write operations. The falling edge of WE#
or CE#, whichever occurs later, latches address infor-
mation and the rising edge of WE# or CE#, whichever
occurs first, latches data/command information.
Commands are accomplished by writing non-specific
address and specific data sequences into the com-
mand register of accessed Flash memory devices.
Writing incorrect address and data values or writ-
ing them in the improper sequence will reset the
device to the read mode.
The byte-wide commands are defined in Tables 6 and
7; word-wide commands are defined in Table 5. Note
that the Erase Suspend (B0h) and Erase Resume
(30h) commands are valid only while the Sector Erase
operation is in progress.
Autoselect Operation
A host system or external card reader/writer can deter-
mine the on-card manufacturer and device I.D. codes.
Codes are available after writing the 90h command to
the command register of a memory device, as shown in
Tables 5 through 7. When the autoselect command is
issued to card address 00000h, the Miniature Card
returns the manufacturer I.D. If the autoselect
command is issued to card address 00001h, the Minia-
ture Card provides the device I.D.
To terminate the autoselect operation, the Read/Reset
command sequence must be written to the same
device. The Autoselect command operates only if the
card is not write protected.
相關PDF資料 |
PDF描述 |
|---|---|
| AMP-25G | Plug-In Amplifier |
| AmPAL20L10-20 | PAL20X10A Series - XOR Registered 24-pin TTL Programmable Array Logic |
| AmPAL20L10AL | PAL20X10A Series - XOR Registered 24-pin TTL Programmable Array Logic |
| AmPAL20L10B | PAL20X10A Series - XOR Registered 24-pin TTL Programmable Array Logic |
| AMPAL22V10 | PAL22V10 Family, AmPAL22V10/A 24-Pin TTL Versatile PAL Device |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMMP-5024 | 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:30kHz - 40 GHz Traveling Wave Amplifier |
| AMMP-5024-BLKG | 功能描述:射頻放大器 100MHz-40GHz RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| AMMP-5024-TR1G | 功能描述:射頻放大器 100MHz-40GHz RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| AMMP-5024-TR2G | 功能描述:射頻放大器 100MHz-40GHz RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| AMMP-5618 | 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:6-20 GHz General Purpose Amplifier |
發布緊急采購，3分鐘左右您將得到回復。