- 您現在的位置：買賣IC網 > PDF目錄223348 > AMIS-30623AAGA (ON SEMICONDUCTOR) STEPPER MOTOR CONTROLLER, 0.8 A, PDSO20 PDF資料下載
參數資料
| 型號： | AMIS-30623AAGA |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 0.8 A, PDSO20 |
| 封裝： | SOIC-20 |
| 文件頁數： | 46/67頁 |
| 文件大?。?/td> | 2400K |
| 代理商： | AMIS-30623AAGA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁
AMIS-30623 LIN Microstepping Motordriver
Data Sheet
If LIN is lost before or at power on, following sequence will be followed. See also Figure 29
1.
If the LIN communication is lost AND FailSafe = 0 there will be no secure positioning. Depending on SleepEn AMIS-30623 will
enter the STOP state or the SLEEP state. See Table 32.
2.
If the LIN communication is lost AND FailSafe = 1 a referencing is started using DualPositioning. A negative motion for half the
positioner range is initiated until the stall position is reached. The motion parameters stored in OTP will be used for this. After
this mechanical end position is reached ActPos will be reset to zero. The direction of the motion is given by the Shaft bit.
If SecPos[10:0] = 0x400:
no Second Motion will be performed.
Depending on SleepEn AMIS-30623 will enter the STOP state or the SLEEP state. See Table 32.
If SecPos[10:0] ≠ 0x400:
A second motion to SecPos is performed. The direction is given by SecPos[10] in combination with Shaft. Motion is
done with parameters from OTP.
Important remarks:
(1) The Secure Position has only a resolution of 9 bit because only the 9 MSB’s will be copied from OTP to RAM.
See also Secure Position
(2) The motion direction to SecPos is given by the Shaft bit in OTP
(3) Same behavior in case of HW2 float (= lost LIN address). See also Hardwired Address HW2
50
AMI Semiconductor
– June 2006, Rev 3.0
www.amis.com
相關PDF資料 |
PDF描述 |
|---|---|
| AMMC-2008 | 0 MHz - 50000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2.3 dB INSERTION LOSS |
| AMR2803R3S/EM | 1-OUTPUT 25 W DC-DC REG PWR SUPPLY MODULE |
| AMR2803R3S/EMPBF | 1-OUTPUT 25 W DC-DC REG PWR SUPPLY MODULE |
| AMR2815S/EM | 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
| AN1458S | DUAL OP-AMP, 4000 uV OFFSET-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMIS-30623AANA | 制造商:AMI 制造商全稱:AMI 功能描述:LIN Microstepping Motordriver |
| AMIS-30623BAGA | 制造商:AMI 制造商全稱:AMI 功能描述:LIN Microstepping Motordriver |
| AMIS-30623BANA | 制造商:AMI 制造商全稱:AMI 功能描述:LIN Microstepping Motordriver |
| AMIS30623C6238G | 功能描述:馬達/運動/點火控制器和驅動器 LIN STEPPER DRIVER STALL RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| AMIS30623C6238RG | 功能描述:馬達/運動/點火控制器和驅動器 LIN STEPPER DRIVER STALL RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。