- 您現在的位置：買賣IC網 > PDF目錄223348 > AMIS-30623AAGA (ON SEMICONDUCTOR) STEPPER MOTOR CONTROLLER, 0.8 A, PDSO20 PDF資料下載
參數資料
| 型號： | AMIS-30623AAGA |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 0.8 A, PDSO20 |
| 封裝： | SOIC-20 |
| 文件頁數： | 18/67頁 |
| 文件大?。?/td> | 2400K |
| 代理商： | AMIS-30623AAGA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁
AMIS-30623 LIN Microstepping Motordriver
Data Sheet
15.2.7. Autarkic functionality in under-voltage condition
Battery voltage management
The AMIS-30623 monitors the battery voltage by means of one threshold and one shutdown level, as illustrated in the state diagram
below. The only condition to reset flags <UV2> and <StepLoss> is to recover a battery voltage higher than UV1 and to receive a
or a GetFullStatus command.
Figure 17: State Diagram Battery Voltage Management
Normal voltage
- <UV2 > = ‘0’
- <StepLoss > = ‘0’
Vbb > UV1 &
LIN frame:
GetStatus
or
GetFullStatus
Vbb < UV2 &
motion ongoin g
Vbb < UV2
(no motion)
Stop mode 1
- <UV2 > = ‘ 1’
- <StepLoss > = ‘0’
- Motor shutdown
(motion disabled)
Stop mode 2
- <UV2 > = ‘ 1’
- <StepLoss > = ‘ 1’
- HardStop
- Motor shutdown
(motion disabled)
Autarkic function
In Stop mode 1 the motor is put in shutdown state. The <UV2> flag is set. In case Vbb > UV1 AMIS-30623 accepts updates of the
target position by means of the reception of SetPosition, SetPositionShort, SetPosParam and GotoSecurePosition
commands, even if the <UV2> flag is NOT prior cleared.
In Stop mode 2 the motor is stopped immediately and put in shutdown state. The <UV2> and <Steploss> flags are set. In case Vbb
> UV1 AMIS-30623 autonomously resumes the motion to the original target position using the stored motor parameters (minimum and
maximum velocity, acceleration, step-mode, run- and hold current) in case no RAM reset occurred.
The flags are only cleared after receiving a GetStatus or GetFullStatus command.
Updates of the target position by means of the reception of SetPosition, SetPositionShort, SetPosParam and
commands is accepted, even if the <UV2> and <Steploss> flags are NOT prior cleared.
Important notes:
1.
In the case of Stop mode 2 care needs to be taken because the accumulated steploss can cause a significant deviation
between physical and stored actual position.
2.
The SetDualPosition command will only be executed after clearing the <UV2> and <Steploss> flags.
3.
RAM reset occurs when Vdd < VddReset (digital Power On Reset level)
4.
The Autarkic function remains active as long as Vdd > VddReset
Logical implementation Autarkic function
The logic uses the <UV2>, <CPFail> and <Steploss> signal NOT the state.
The state is set one clock after the signal and would therefore slow down the reaction time. Also the state can only be cleared after a
or GetFullStatus command which prevents the autonomous function.
Only <UV2> and <CPFail> are applicable for finishing the motion to the original target position:
<UV2> needs to be cleared to leave the Shutdown State
<CPFail> needs to be cleared to avoid a new HardStop after entering the GotoPos state
25
AMI Semiconductor
– June 2006, Rev 3.0
www.amis.com
相關PDF資料 |
PDF描述 |
|---|---|
| AMMC-2008 | 0 MHz - 50000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2.3 dB INSERTION LOSS |
| AMR2803R3S/EM | 1-OUTPUT 25 W DC-DC REG PWR SUPPLY MODULE |
| AMR2803R3S/EMPBF | 1-OUTPUT 25 W DC-DC REG PWR SUPPLY MODULE |
| AMR2815S/EM | 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
| AN1458S | DUAL OP-AMP, 4000 uV OFFSET-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMIS-30623AANA | 制造商:AMI 制造商全稱:AMI 功能描述:LIN Microstepping Motordriver |
| AMIS-30623BAGA | 制造商:AMI 制造商全稱:AMI 功能描述:LIN Microstepping Motordriver |
| AMIS-30623BANA | 制造商:AMI 制造商全稱:AMI 功能描述:LIN Microstepping Motordriver |
| AMIS30623C6238G | 功能描述:馬達/運動/點火控制器和驅動器 LIN STEPPER DRIVER STALL RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| AMIS30623C6238RG | 功能描述:馬達/運動/點火控制器和驅動器 LIN STEPPER DRIVER STALL RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。