參數資料
型號： AMIS-30623AAGA
廠商： ON SEMICONDUCTOR
元件分類： 運動控制電子
英文描述： STEPPER MOTOR CONTROLLER, 0.8 A, PDSO20
封裝： SOIC-20
文件頁數： 17/67頁
文件大?。?/td> 2400K
代理商： AMIS-30623AAGA
AMIS-30623 LIN Microstepping Motordriver
Data Sheet
15.2.4. Sleep Mode
When entering sleep mode, the stepper-motor can be driven to its secure position. After which, the circuit is completely powered down,
apart from the LIN receiver, which remains active to detect dominant state on the bus. In case sleep mode is entered while a motion is
ongoing, a transition will occur towards secure position as described in Positioning and Motion Control provided SecPos is enabled.
Otherwise, SoftStop is performed.
Sleep mode can be entered in the following cases:
The circuit receives a LIN frame with identifier 0x3C and first data byte containing 0x00, as required by LIN specification
rev 1.3. See Sleep
In case the SleepEn bit =1 and the LIN bus remains inactive (or is lost) during more than 25000 time slots (1.30s at 19.2kbit/s),
a time-out signal switches the circuit to sleep mode. See also
The circuit will return to normal mode if a valid LIN frame is received while entering the sleep mode (this valid frame can be addressed
to another slave).
15.2.5. Thermal Shutdown Mode
When thermal shutdown occurs, the circuit performs a SoftStop command and goes to Motor shutdown mode (see below).
15.2.6. Temperature Management
The AMIS-30623 monitors temperature by means of two thresholds and one shutdown level, as illustrated in the state diagram below.
The only condition to reset flags <TW> and <TSD> (respectively thermal warning and thermal shutdown) is to be at a temperature lower
than Ttw and to get the occurrence of a GetStatus or a GetFullStatus LIN frame.
Figure 16: State Diagram Temperature Management
Normal Temp.
- <Tinfo> = “00”
- <TW> = ‘0’
- <TSD> = ‘0’
T° < Ttw &
LIN frame:
GetStatus
or
GetFullStatus
T° > Ttw
Thermal warning
- <Tinfo> = “10”
- <TW> = ‘1’
- <TSD> = ‘0’
T° > Ttsd
Thermal shutdown
- <Tinfo> = “11”
- <TW> = ‘1’
- <TSD> = ‘1’
- SoftStop if
motion ongoing
- Motor shutdown
(motion disabled)
Post thermal
warning
- <Tinfo> = “00”
- <TW> = ‘1’
- <TSD> = ‘0’
T° > Tlow
T° > Ttw
T° < Ttsd
T° > Ttsd
Post thermal
shutdown 1
- <Tinfo> = “10”
- <TW> = ‘1’
- <TSD> = ‘1’
- Motor shutdown
(motion disabled)
Post thermal
shutdown 2
- <Tinfo> = “00”
- <TW> = ‘1’
- <TSD> = ‘1’
- Motor shutdown
(motion disabled)
Low Temp.
- <Tinfo> = “01”
- <TW> = ‘0’
- <TSD> = ‘0’
T° < Ttw
T° > Ttw
T° < Tlow
T° < Ttw
24
AMI Semiconductor
– June 2006, Rev 3.0
www.amis.com
相關PDF資料
PDF描述
AMMC-2008 0 MHz - 50000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2.3 dB INSERTION LOSS
AMR2803R3S/EM 1-OUTPUT 25 W DC-DC REG PWR SUPPLY MODULE
AMR2803R3S/EMPBF 1-OUTPUT 25 W DC-DC REG PWR SUPPLY MODULE
AMR2815S/EM 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE
AN1458S DUAL OP-AMP, 4000 uV OFFSET-MAX, PDSO8
相關代理商/技術參數
參數描述
AMIS-30623AANA 制造商:AMI 制造商全稱:AMI 功能描述:LIN Microstepping Motordriver
AMIS-30623BAGA 制造商:AMI 制造商全稱:AMI 功能描述:LIN Microstepping Motordriver
AMIS-30623BANA 制造商:AMI 制造商全稱:AMI 功能描述:LIN Microstepping Motordriver
AMIS30623C6238G 功能描述:馬達/運動/點火控制器和驅動器 LIN STEPPER DRIVER STALL RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
AMIS30623C6238RG 功能描述:馬達/運動/點火控制器和驅動器 LIN STEPPER DRIVER STALL RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*