- 您現在的位置：買賣IC網 > PDF目錄366550 > AM79C975 (Advanced Micro Devices, Inc.) PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY PDF資料下載
參數資料
| 型號： | AM79C975 |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
| 中文描述： | PCnet⑩快速三單芯片10/100 Mbps的PCI以太網控制器集成PHY |
| 文件頁數： | 56/304頁 |
| 文件大?。?/td> | 2092K |
| 代理商： | AM79C975 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁當前第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁第257頁第258頁第259頁第260頁第261頁第262頁第263頁第264頁第265頁第266頁第267頁第268頁第269頁第270頁第271頁第272頁第273頁第274頁第275頁第276頁第277頁第278頁第279頁第280頁第281頁第282頁第283頁第284頁第285頁第286頁第287頁第288頁第289頁第290頁第291頁第292頁第293頁第294頁第295頁第296頁第297頁第298頁第299頁第300頁第301頁第302頁第303頁第304頁
56
Am79C973/Am79C975
P R E L I M I N A R Y
Whenever the Am79C973/Am79C975 controller is the
current bus master and a data parity error occurs, SINT
(CSR5, bit 11) will be set to 1. When SINT is set, INTA
is asserted if the enable bit SINTE (CSR5, bit 10) is set
to 1. This mechanism can be used to inform the driver
of the system error. The host can read the PCI Status
register to determine the exact cause of the interrupt.
The setting of SINT due to a data parity error is not
dependent on the setting of PERREN (PCI Command
register, bit 6).
By default, a data parity error does not affect the state
of the MAC engine. The Am79C973/Am79C975 con-
troller treats the data in all bus master transfers that have
a parity error as if nothing has happened. All network
activity continues.
Advanced Parity Error Handling
For all DMA cycles, the Am79C973/Am79C975 control-
ler provides a second, more advanced level of parity
error handling. This mode is enabled by setting APER-
REN (BCR20, bit 10) to 1. When APERREN is set to 1,
the BPE bits (RMD1 and TMD1, bit 23) are used to
indicate parity error in data transfers to the receive and
transmit buffers. Note that since the advanced parity
error handling uses an additional bit in the descriptor,
SWSTYLE (BCR20, bits 7-0) must be set to 2 or 3 to
program the Am79C973/Am79C975 controller to use
32-bit software structures. The Am79C973/Am79C975
controller will react in the following way when a data
parity error occurs:
I
Initialization block read: STOP (CSR0, bit 2) is set to
1 and causes a STOP_RESET of the device.
I
Descriptor ring read: Any on-going network activity
is terminated in an orderly sequence and then STOP
(CSR0, bit 2) is set to 1 to cause a STOP_RESET
of the device.
I
Descriptor ring write: Any on-going network activity
is terminated in an orderly sequence and then STOP
(CSR0, bit 2) is set to 1 to cause a STOP_RESET
of the device.
I
Transmit buffer read: BPE (TMD1, bit 23) is set in
the current transmit descriptor. Any on-going net-
work transmission is terminated in an orderly se-
quence.
I
Receive buffer write: BPE (RMD1, bit 23) is set in
the last receive descriptor associated with the frame.
Terminating on-going network transmission in an or-
derly sequence means that if less than 512 bits have
been transmitted onto the network, the transmission
will be terminated immediately, generating a runt
packet.
If 512 bits or more have been transmitted, the message
will have the current FCS inverted and appended at the
next byte boundary to guarantee an FCS error is de-
tected at the receiving station.
APERREN does not affect the reporting of address
parity errors or data parity errors that occur when the
Am79C973/Am79C975 controller is the target of the
transfer.
Initialization Block DMA Transfers
During execution of the Am79C973/Am79C975 con-
troller bus master initialization procedure, the
Am79C973/Am79C975 microcode will repeatedly re-
quest DMA transfers from the BIU. During each of
these initialization block DMA transfers, the BIU will
perform two data transfer cycles reading one DWord
per transfer and then it will relinquish the bus. When
SSIZE32 (BCR20, bit 8) is set to 1 (i.e., the initialization
block is organized as 32-bit software structures), there
are seven DWords to transfer during the bus master ini-
tialization procedure, so four bus master-ship periods
are needed in order to complete the initialization se-
quence. Note that the last DWord transfer of the last
bus mastership period of the initialization sequence ac-
cesses an unneeded location. Data from this transfer is
discarded internally. When SSIZE32 is cleared to 0
(i.e., the initialization block is organized as 16-bit soft-
ware structures), then three bus mastership periods
are needed to complete the initialization sequence.
The Am79C973/Am79C975 supports two transfer
modes for reading the initialization block: non-burst and
burst mode, with burst mode being the preferred mode
when the Am79C973/Am79C975 controller is used in a
PCI bus application. See Figure 23 and Figure 24.
When BREADE is cleared to 0 (BCR18, bit 6), all initial-
ization block read transfers will be executed in non-
burst mode. There is a new address phase for every
data phase. FRAME will be dropped between the two
transfers. The two phases within a bus mastership pe-
riod will have addresses of ascending contiguous or-
der.
When BREADE is set to 1 (BCR18, bit 6), all initializa-
tion block read transfers will be executed in burst mode.
AD[1:0] will be 0 during the address phase indicating a
linear burst order.
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C973 | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
| AM79C973KCW | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
| AM79C975KCW | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
| AM79C973VCW | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
| AM79C975VCW | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C975BKC\\W | 制造商:Advanced Micro Devices 功能描述: |
| AM79C975BKC\W | 制造商:Advanced Micro Devices 功能描述: |
| AM79C975BKD\\W | 制造商:Advanced Micro Devices 功能描述: |
| AM79C975BKD\W | 制造商:Advanced Micro Devices 功能描述:PCnet-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY 制造商:AMD (Advanced Micro Devices) 功能描述:PCnet-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
| AM79C975BKDW | 制造商:Advanced Micro Devices 功能描述:PCnet-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY 制造商:AMD (Advanced Micro Devices) 功能描述:PCnet-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
發布緊急采購，3分鐘左右您將得到回復。