參數資料
型號： ADV7180
廠商： Analog Devices, Inc.
英文描述： 10-Bit, 4 x Oversampling SDTV Video Decoder
中文描述： 10位，4個采樣標清視頻解碼器
文件頁數： 74/112頁
文件大?。?/td> 1320K
代理商： ADV7180
ADV7180
MPU PORT DESCRIPTION
The ADV7180 supports a 2-wire (I
2
C-compatible) serial inter-
face. Two inputs, serial data (SDA) and serial clock (SCLK),
carry information between the ADV7180 and the system I
2
C
master controller. Each slave device is recognized by a unique
address. The ADV7180 I
2
C port allows the user to set up and
configure the decoder and to read back captured VBI data. The
ADV7180 has four possible slave addresses for both read and
write operations, depending on the logic level of the ALSB pin.
The four unique addresses are shown in Table 100. The ADV7180
ALSB pin controls Bit 1 of the slave address. By altering the ALSB,
it is possible to control two ADV7180s in an application without
having the conflict of using the same slave address. The LSB (Bit 0)
sets either a read or write operation. Logic 1 corresponds to a
read operation; Logic 0 corresponds to a write operation.
Rev. A | Page 74 of 112
Table 100. I
2
C Address for ADV7180
ALSB
R/W
0
0
0
1
1
0
1
1
Slave Address
0x40
0x41
0x42
0x43
To control the device on the bus, a specific protocol must be
followed. First, the master initiates a data transfer by establishing
a start condition, which is defined by a high-to-low transition
on SDA while SCLK remains high. This indicates that an address/
data stream follows. All peripherals respond to the start condition
and shift the next eight bits (the 7-bit address plus the R/W bit).
The bits are transferred from MSB down to LSB. The peripheral
that recognizes the transmitted address responds by pulling the
data line low during the ninth clock pulse; this is known as an
acknowledge bit. All other devices withdraw from the bus at
this point and maintain an idle condition. The idle condition is
where the device monitors the SDA and SCLK lines for the start
condition and the correct transmitted address. The R/W bit
determines the direction of the data. Logic 0 on the LSB of the
first byte means that the master writes information to the
peripheral. Logic 1 on the LSB of the first byte means that the
master reads information from the peripheral.
The ADV7180 acts as a standard slave device on the bus. The
data on the SDA pin is eight bits long, supporting the 7-bit
address plus the R/W bit. The device has 249 subaddresses to
enable access to the internal registers. It therefore interprets the
first byte as the device address and the second byte as the
starting subaddress. The subaddresses auto-increment, allowing
data to be written to or read from the starting subaddress. A
data transfer is always terminated by a stop condition. The user
can also access any unique subaddress register on a one-by-one
basis without updating all the registers.
Stop and start conditions can be detected at any stage during the
data transfer. If these conditions are asserted out of sequence with
normal read and write operations, they cause an immediate
jump to the idle condition. During a given SCLK high period,
the user should only issue one start condition, one stop condition,
or a single stop condition followed by a single start condition. If
an invalid subaddress is issued by the user, the ADV7180 does
not issue an acknowledge and returns to the idle condition.
In auto-increment mode, if the user exceeds the highest
subaddress, the following action is taken:
In read mode, the highest subaddress register contents
continue to be output until the master device issues a no
acknowledge. This indicates the end of a read. A no
acknowledge condition is when the SDA line is not pulled
low on the ninth pulse.
In write mode, the data for the invalid byte is not loaded
into any subaddress register. A no acknowledge is issued by
the ADV7180, and the part returns to the idle condition.
SDATA
SCLOCK
START ADDR
ACK
ACK
DATA
ACK
STOP
SUBADDRESS
1–7
1–7
8
9
8
9
1–7
8
9
S
P
R/W
0
Figure 48. Bus Data Transfer
S
WRITE
SEQUENCE
SLAVE ADDR
A(S)
SUB ADDR
A(S)
DATA
A(S)
DATA
A(S)
P
S
READ
SEQUENCE
SLAVE ADDR
SLAVE ADDR
A(S)
SUB ADDR
A(S) S
A(S)
DATA
A(M)
DATA
A(M) P
S = START BIT
P = STOP BIT
A(S) = ACKNOWLEDGE BY SLAVE
A(M) = ACKNOWLEDGE BY MASTER
Figure 49. Read and Write Sequence
A(S) = NO ACKNOWLEDGE BY SLAVE
A(M) = NO ACKNOWLEDGE BY MASTER
LSB = 1
LSB = 0
0
相關PDF資料
PDF描述
ADV7180BCPZ 10-Bit, 4 x Oversampling SDTV Video Decoder
ADV7180BSTZ 10-Bit, 4 x Oversampling SDTV Video Decoder
ADV7181 Multiformat SDTV Video Decoder
ADV7181B Multiformat SDTV Video Decoder
ADV7181BBCPZ Multiformat SDTV Video Decoder
相關代理商/技術參數
參數描述
ADV7180_12 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 4?? Oversampling SDTV Video Decoder
ADV7180BCP32Z 制造商:Analog Devices 功能描述:10-BIT, 4? OVERSAMPLING SDTV VIDEO DECODER - Trays
ADV7180BCP32Z-RL 制造商:Analog Devices 功能描述:IC
ADV7180BCPZ 功能描述:IC VIDEO DECODER SDTV 40-LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 標準包裝:250 系列:- 類型:電平移位器 應用:LCD 電視機/監控器 安裝類型:表面貼裝 封裝/外殼:28-WFQFN 裸露焊盤 供應商設備封裝:28-WQFN（4x4）裸露焊盤 包裝:帶卷 (TR) 其它名稱:296-32523-2TPS65198RUYT-ND
ADV7180BCPZ 制造商:Analog Devices 功能描述:IC VIDEO DECODER 10BIT 57.27MSPS LFCSP40
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*