參數資料
型號： ADM1027ARQZ-RL7
廠商： ON Semiconductor
文件頁數： 6/56頁
文件大?。?/td> 1822K
描述： IC REMOTE THERMAL CTLR 24QSOP
產品變化通告： MFG CHG Notification ADI to ON Semi
Product Discontinuation Notice 25/Aug/2008
Product Obsolescence 30/Sept/2009
標準包裝： 1,000
系列： dBCool®
功能： 風扇控制，溫度監控器
傳感器類型： 內部和外部
感應溫度： 0°C ~ 105°C，外部傳感器
精確度： ±1°C
拓?fù)洌?/td> ADC，比較器，風扇速度計數器，多路復用器，寄存器庫
輸出類型： SMBus?
輸出警報： 無
輸出風扇： 是
電源電壓： 3 V ~ 5.5 V
工作溫度： 0°C ~ 105°C
安裝類型： 表面貼裝
封裝/外殼： 24-SSOP（0.154"，3.90mm 寬）
供應商設備封裝： 24-QSOP
包裝： 帶卷 (TR)
REV. A
6
ADM1027
FUNCTIONAL DESCRIPTION
General Description
The ADM1027 is a complete systems monitor and multiple fan
controller for any system requiring monitoring and cooling. The
device communicates with the system via a serial system
management bus. The serial bus controller has an optional
address line for device selection (Pin 14), a serial data line
for reading and writing addresses and data (Pin 1), and an input
line for the serial clock (Pin 2). All control and programming
functions of the ADM1027 are performed over the serial bus. In
addition, one of the pins can be reconfigured as an SMBALERT
output to indicate out-of-limit conditions.
Measurement Inputs
The device has six measurement inputs, four for voltage and
two for temperature. It can also measure its own supply voltage
and can measure ambient temperature with its on-chip tempera-
ture sensor.
Pins 20 to 23 are analog inputs with on-chip attenuators,
configured to monitor 5 V, 12 V, 2.5 V, and the processor core
voltage (2.25 V input), respectively.
Power is supplied to the chip via Pin 4, which the system also
uses to monitor V
CC
. In PCs, this pin is normally connected to a
3.3 V standby supply. This pin can, however, be connected to a
5 V supply and monitor it without overranging.
Remote temperature sensing is provided by the D1+/ and
D2+/ inputs, to which diode-connected, external temperature-
sensing transistors such as a 2N3906 or CPU thermal diode
may be connected.
The ADC also accepts input from an on-chip band gap tem-
perature sensor that monitors system ambient temperature.
Sequential Measurement
When the ADM1027 monitoring sequence is started, it cycles
sequentially through the measurement of analog inputs and the
temperature sensors. Measured values from these inputs are
stored in value registers. These can be read out over the serial
bus, or can be compared with programmed limits stored in the
limit registers. The results of out-of-limit comparisons are stored
in the status registers, which can be read over the serial bus to
flag out-of-limit conditions.
Processor Voltage ID
Five digital inputs (VID0 to VID4  Pins 5 to 8 and 19) read
the processor Voltage ID code and store it in the VID register,
from which it can be read out by the management system over
the serial bus. The VID code monitoring function is compatible
with both VRM9.x and future VRM10 solutions. The VID code
monitoring function is compatible with VRM9.x.
ADM1027 Address Selection
Pin 13 is the dual function PWM3/ADDRESS ENABLE pin.
If Pin 13 is pulled low on power-up, the ADM1027 will read the
state of Pin 14 (TACH4/ADDRESS SELECT pin) to determine
the ADM1027 slave address. If Pin 13 is high on power-up, then
the ADM1027 will default to SMBus slave address 0x5C. This
function is described later in more detail.
Internal Registers of the ADM1027
A brief description of the ADM1027s principal internal regis-
ters follows. More detailed information on the function of each
register is given in Tables IV to XXXVI.
Configuration Registers
Provide control and configuration of the ADM1027, including
alternate pinout functionality.
Address Pointer Register
Contains the address that selects one of the other internal registers.
When writing to the ADM1027, the first byte of data is always a
register address, which is written to the Address Pointer Register.
Status Registers
Provide the status of each limit comparison and are used to
signal out-of-limit conditions on the temperature, voltage, or
fan speed channels. If Pin 10 is configured as SMBALERT,
then this pin will assert low whenever a status bit gets set.
Interrupt Mask Registers
Allow each interrupt status event to be masked when Pin 10 is
configured as an SMBALERT output. This affects only the
SMBALERT output and not the bits in the status register.
VID Register
The status of the VID0 to VID4 pins of the processor can be
read from this register.
Value and Limit Registers
The results of analog voltage inputs, temperature, and fan speed
measurements are stored in these registers, along with their limit
values.
Offset Registers
Allow each temperature channel reading to be offset by a twos
complement value written to these registers.
T
MIN
 Registers
Program the starting temperature for each fan under automatic
fan speed control.
T
RANGE
 Registers
Program the temperature-to-fan speed control slope in automatic
Fan Speed Control Mode for each PWM output.
Enhance Acoustics Registers
Allow each PWM output controlling fan to be tweaked to enhance
the systems acoustics.
Rev. 3 | Page 6 of 56 | www.onsemi.com
相關PDF資料
PDF描述
ADM1029ARQZ-R7 IC SENSOR 2TEMP/FAN CTRL 24QSOP
ADM1030ARQZ-RL7 IC SNSR TEMP/FAN PWM CTRL 16QSOP
ADM1032ARZ-REEL IC TEMP MONITOR 85DEG 8SOIC
ADM1033ARQZ-RL7 IC THERM/FAN SPEED CTLR 16-QSOP
ADM1034ARQZ-REEL IC THERM/FAN SPEED CTRLR 16-QSOP
相關代理商/技術參數
參數描述
ADM1027ARQZ-RL71 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:dBCOOLa?￠ Remote Thermal Controller and Voltage Monitor
ADM1028 制造商:AD 制造商全稱:Analog Devices 功能描述:Remote Thermal Diode Monitor with Linear Fan Control
ADM1028ARQ 功能描述:IC SENSOR TEMP/FAN CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1028ARQ-REEL7 制造商:Rochester Electronics LLC 功能描述:TDM + LINEAR FAN CONTROL I.C. - Tape and Reel
ADM1029 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual PWM Fan Controller and Temperature Monitor for High Availability Systems
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*