參數資料
型號： ADAU1761BCPZ
廠商： Analog Devices Inc
文件頁數： 43/92頁
文件大?。?/td> 0K
描述： IC SIGMADSP CODEC PLL 32LFCSP
設計資源： Stereo Digital Microphone Input Using ADAU1761 and ADMP421 (CN0078)
標準包裝： 1
系列： SigmaDSP®
類型： 音頻編解碼器
數據接口： 串行
分辨率（位）： 24 b
ADC / DAC 數量： 2 / 2
三角積分調變： 是
電壓 - 電源，模擬： 1.8 V ~ 3.65 V
電壓 - 電源，數字： 1.63V ~ 3.65V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 32-VFQFN 裸露焊盤，CSP
供應商設備封裝： 32-LFCSP-VQ
包裝： 托盤
產品目錄頁面： 776 (CN2011-ZH PDF)
配用： EVAL-ADAU1761Z-ND - BOARD EVAL FOR ADAU1761
ADAU1761
Rev. C | Page 48 of 92
Table 27. Parameter RAM Read/Write Format (Single Address)
Byte 0
Byte 1
Byte 2
Byte 3
Bytes[4:6]
chip_adr[6:0], R/W
param_adr[15:8]
param_adr[7:0]
0000, param[27:24]
param[23:0]
Table 28. Parameter RAM Block Read/Write Format (Burst Mode)
Byte 0
Byte 1
Byte 2
Byte 3
Bytes[4:6]
Bytes[7:10]
Bytes[11:14]
chip_adr[6:0], R/W
param_adr[15:8]
param_adr[7:0]
0000, param[27:24]
param[23:0]
<—param_adr—>
param_adr + 1
param_adr + 2
Table 29. Program RAM Read/Write Format (Single Address)
Byte 0
Byte 1
Byte 2
Bytes[3:7]
chip_adr[6:0], R/W
prog_adr[15:8]
prog_adr[7:0]
prog[39:0]
Table 30. Program RAM Block Read/Write Format (Burst Mode)
Byte 0
Byte 1
Byte 2
Bytes[3:7]
Bytes[8:12]
Bytes[13:17]
chip_adr[6:0], R/W
prog_adr[15:8]
prog_adr[7:0]
prog[39:0]
<—prog_adr—>
prog_adr + 1
prog_adr + 2
SOFTWARE SAFELOAD
To update parameters in real time while avoiding pop and click
noises on the output, the ADAU1761 uses a software safeload
mechanism. The software safeload mechanism enables the
SigmaDSP core to load new parameters into RAM while guar-
anteeing that the parameters are not in use. This prevents an
undesirable condition where an instruction could execute with
a mix of old and new parameters.
SigmaStudio sets up the necessary code and parameters auto-
matically for new projects. The safeload code, along with other
initialization code, fills the first 39 locations in program RAM.
The first eight parameter RAM locations (Address 0x0000 to
Address 0x0007) are configured by default in SigmaStudio as
described in Table 31.
Table 31. Software Safeload Parameter RAM Defaults
Address (Hex)
Function
0x0000
Modulo RAM size
0x0001
Safeload Data 1
0x0002
Safeload Data 2
0x0003
Safeload Data 3
0x0004
Safeload Data 4
0x0005
Safeload Data 5
0x0006
Safeload target address (offset of 1)
0x0007
Number of words to write/safeload trigger
Address 0x0000, which controls the modulo RAM size, is set
by SigmaStudio and is based on the dynamic address generator
mode of the project.
Parameter RAM Address 0x0001 to Address 0x0005 are the five
data slots for storing the data to be safeloaded. The safeload
parameter space contains five data slots by default because most
standard signal processing algorithms have five parameters or less.
Address 0x0006 is the target address in parameter RAM (with
an offset of 1). This designates the first address to be written.
If more than one word is written, the address increments auto-
matically for each data-word. Up to five sequential parameter
RAM locations can be updated with safeload during each audio
frame. The target address offset of 1 is used because the write
address is calculated relative to the address of the data, which
starts at Address 0x0001. Therefore, to update a parameter at
Address 0x000A, the target address is 0x0009.
Address 0x0007 designates the number of words to be written
into the parameter RAM during the safeload. A biquad filter
uses all five safeload data addresses. A simple mono gain cell
uses only one safeload data address. Writing to Address 0x0007
also triggers the safeload write to occur in the next audio frame.
The safeload mechanism is software based and executes once
per audio frame. Therefore, system designers must take care
when designing the communication protocol. A delay equal to
or greater than the sampling period (the inverse of sampling
frequency) is required between each safeload write. A sample
rate of 48 kHz equates to a delay of at least 21 μs. If this delay
is not observed, the downloaded data is corrupted.
相關PDF資料
PDF描述
MC9328MXSVP10R2 IC MCU I.MXS 100MHZ 225-MAPBGA
MC9S12XEQ384CAG MCU 16BIT 384K FLASH 144-LQFP
VE-B4W-IW-B1 CONVERTER MOD DC/DC 5.5V 100W
MC705C8ACFNER IC MCU 8BIT 44-PLCC
MC908GZ32MFAE IC MCU 8BIT 32K FLASH 48-LQFP
相關代理商/技術參數
參數描述
ADAU1761BCPZ 制造商:Analog Devices 功能描述:IC, AUDIO CODEC, 24BIT, 96KHZ, LFCSP-32
ADAU1761BCPZ-R7 功能描述:IC SIGMADSP CODEC PLL 32LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 編解碼器 系列:SigmaDSP® 標準包裝:2,500 系列:- 類型:立體聲音頻 數據接口:串行 分辨率（位）:18 b ADC / DAC 數量:2 / 2 三角積分調變:是 S/N 比，標準 ADC / DAC (db):81.5 / 88 動態范圍，標準 ADC / DAC (db):82 / 87.5 電壓 - 電源，模擬:2.6 V ~ 3.3 V 電壓 - 電源，數字:1.7 V ~ 3.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-WFQFN 裸露焊盤 供應商設備封裝:48-TQFN-EP（7x7） 包裝:帶卷 (TR)
ADAU1761BCPZ-RL 功能描述:IC SIGMADSP CODEC PLL 32LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 編解碼器 系列:SigmaDSP® 標準包裝:2,500 系列:- 類型:立體聲音頻 數據接口:串行 分辨率（位）:18 b ADC / DAC 數量:2 / 2 三角積分調變:是 S/N 比，標準 ADC / DAC (db):81.5 / 88 動態范圍，標準 ADC / DAC (db):82 / 87.5 電壓 - 電源，模擬:2.6 V ~ 3.3 V 電壓 - 電源，數字:1.7 V ~ 3.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-WFQFN 裸露焊盤 供應商設備封裝:48-TQFN-EP（7x7） 包裝:帶卷 (TR)
ADAU1772BCPZ 功能描述:接口—CODEC Low Latency Noise and Power CODEC RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
ADAU1772BCPZ-R7 功能描述:接口—CODEC Low Latency Noise and Power CODEC RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*