參數資料
型號： AD9959BCPZ
廠商： Analog Devices Inc
文件頁數： 25/44頁
文件大?。?/td> 0K
描述： IC DDS QUAD 10BIT DAC 56LFCSP
產品培訓模塊： Direct Digital Synthesis Tutorial Series (1 of 7): Introduction
Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action
Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter
Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction
Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter
Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator
設計資源： Phase Coherent FSK Modulator (CN0186)
標準包裝： 1
分辨率（位）： 10 b
主 fclk： 500MHz
調節字寬（位）： 32 b
電源電壓： 1.71 V ~ 1.96 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 56-VFQFN 裸露焊盤，CSP
供應商設備封裝： 56-LFCSP-VQ（8x8）
包裝： 托盤
產品目錄頁面： 552 (CN2011-ZH PDF)
AD9959
Rev. B | Page 31 of 44
SERIAL I/O PORT
OVERVIEW
The AD9959 serial I/O port offers multiple configurations to
provide significant flexibility. The serial I/O port offers an SPI-
compatible mode of operation that is virtually identical to the
SPI operation found in earlier Analog Devices DDS products.
The flexibility is provided by four data pins (SDIO_0, SDIO_1,
SDIO_2, SDIO_3) that allow four programmable modes of
serial I/O operation.
Three of the four data pins (SDIO_1, SDIO_2, SDIO_3) can be
used for functions other than serial I/O port operation. These pins
can also be used to initiate a ramp-up or ramp-down (RU/RD)
of the 10-bit amplitude output scalar. In addition, SDIO_3 can
be used to provide the SYNC_I/O function that resynchronizes
the serial I/O port controller if it is out of proper sequence.
The maximum speed of the serial I/O port SCLK is 200 MHz,
but the four data pins (SDIO_0, SDIO_1, SDIO_2, SDIO_3)
can be used to further increase data throughput. The maximum
data throughput using all the SDIO pins (SDIO_0, SDIO_1,
SDIO_2, SDIO_3) is 800 Mbps.
Note that all channels share Register 0x03 to Register 0x18, which
are shown in the Register Maps and Bit Descriptions section.
This address sharing enables all four DDS channels to be written
to simultaneously. For example, if a common frequency tuning
word is desired for all four channels, it can be written once
through the serial I/O port to all four channels. This is the
default mode of operation (all channels enabled). To enable
each channel to be independent, the four channel enable bits
found in the channel select register (CSR, Register 0x00) must
be used.
There are effectively four sets or copies of addresses (Register 0x03
to Register 0x18) that the channel enable bits can access to provide
channel independence. See the Descriptions for Control Registers
section for further details of programming channels that are
common to or independent from each other. To properly read
back Register 0x03 to Register 0x18, the user must enable only
one channel enable bit at a time.
Serial operation of the AD9959 occurs at the register level,
not the byte level; that is, the controller expects that all bytes
contained in the register address are accessed. The SYNC_I/O
function can be used to abort an I/O operation, thereby allowing
fewer than all bytes to be accessed. This feature can be used to
program only a part of the addressed register. Note that only
completed bytes are affected.
There are two phases to a serial communications cycle. Phase 1
is the instruction cycle, which writes the instruction byte into
the AD9959. Each bit of the instruction byte is registered on
each corresponding rising edge of SCLK. The instruction byte
defines whether the upcoming data transfer is a write or read
operation. The instruction byte contains the serial address of
the address register.
Phase 2 of the I/O cycle consists of the actual data transfer
(write/read) between the serial port controller and the serial
port buffer. The number of bytes transferred during this phase
of the communication cycle is a function of the register being
accessed. The actual number of additional SCLK rising edges
required for the data transfer and instruction byte depends on
the number of bytes in the register and the serial I/O mode of
operation.
For example, when accessing Function Register 1 (FR1), which
is three bytes wide, Phase 2 of the I/O cycle requires that three
bytes be transferred. After transferring all data bytes per the
instruction byte, the communication cycle is completed for that
register.
At the completion of a communication cycle, the AD9959 serial
port controller expects the next set of rising SCLK edges to be
the instruction byte for the next communication cycle. All data
written to the AD9959 is registered on the rising edge of SCLK.
Data is read on the falling edge of SCLK (see Figure 43 through
Figure 49). The timing specifications for Figure 41 and Figure 42
are described in Table 25.
tPRE
tDSU
tSCLK
tSCLKPWL
tSCLKPWH
tDHLD
CS
SCLK
SDIO_x
05
24
6-
02
3
Figure 41. Setup and Hold Timing for the Serial I/O Port
tDV
CS
SCLK
SDIO_x
SDO (SDIO_2)
05
24
6-
0
24
Figure 42. Timing Diagram for Data Read for Serial I/O Port
Table 25. Timing Specifications
Parameter
Min
Unit
Description
tPRE
1.0
ns min
CS setup time
tSCLK
5.0
ns min
Period of serial data clock
tDSU
2.2
ns min
Serial data setup time
tSCLKPWH
2.2
ns min
Serial data clock pulse width high
tSCLKPWL
1.6
ns min
Serial data clock pulse width low
tDHLD
0
ns min
Serial data hold time
tDV
12
ns min
Data valid time
相關PDF資料
PDF描述
VE-2WT-IY-F2 CONVERTER MOD DC/DC 6.5V 50W
VE-2WR-IY-F4 CONVERTER MOD DC/DC 7.5V 50W
VE-2WR-IY-F1 CONVERTER MOD DC/DC 7.5V 50W
VE-2WP-IY-F3 CONVERTER MOD DC/DC 13.8V 50W
VE-2WN-IY-F2 CONVERTER MOD DC/DC 18.5V 50W
相關代理商/技術參數
參數描述
AD9959BCPZ1 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 500 MSPS DDS with 10-Bit DACs
AD9959BCPZ-REEL7 功能描述:IC DDS QUAD 10BIT DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 調節字寬（位）:32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
AD9959BCPZ-REEL71 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 500 MSPS DDS with 10-Bit DACs
AD995PCBZ 制造商:AD 制造商全稱:Analog Devices 功能描述:1 GSPS Quadrature Digital Upconverter w/18-Bit IQ Data Path and 14-Bit DAC
AD9960BSTZ 功能描述:RFID應答器 MxFE for RFID Reader Transceiver RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*