- 您現在的位置：買賣IC網 > PDF目錄10978 > AD9954YSVZ (Analog Devices Inc)IC DDS DAC 14BIT 1.8V 48-TQFP PDF資料下載
參數資料
| 型號： | AD9954YSVZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 22/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DDS DAC 14BIT 1.8V 48-TQFP |
| 產品培訓模塊： | Direct Digital Synthesis Tutorial Series (1 of 7): Introduction Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator |
| 標準包裝： | 1 |
| 分辨率（位）： | 14 b |
| 主 fclk： | 400MHz |
| 調節字寬（位）： | 32 b |
| 電源電壓： | 1.71 V ~ 1.96 V |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TQFP 裸露焊盤 |
| 供應商設備封裝： | 48-TQFP 裸露焊盤（7x7） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 552 (CN2011-ZH PDF) |
| 配用： | AD9954/PCBZ-ND - BOARD EVAL FOR 9954 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
AD9954
Rev. B | Page 29 of 40
CONTROL REGISTER BIT DESCRIPTIONS
Control Function Register No. 1 (CFR1)
The CFR1 is used to control the various functions, features,
and modes of the AD9954. The functionality of each bit follows.
CFR1<31>: RAM Enable Bit
CFR1<31> = 0 (default). The RAM is disabled for operation.
Either single-tone mode of operation or linear sweep mode of
operation is enabled.
CFR1<31> = 1. The RAM is enabled for operation. Access
control for normal operation is controlled via the mode control
bits of the RSCW for the current profile.
CFR1<30>: RAM Destination Bit
If CFR1<31> is cleared, CFR1<30> is ignored.
CFR1<30> = 0 (default). If CFR1<31> is set, the RAM output
drives the phase accumulator (provides the FTW).
CFR1<30> = 1. If CFR1<31> is set, the RAM output drives the
phase-offset adder (POW).
CFR1<29:27>: Internal Profile Control Bits
These bits cause the profile bits to be ignored when the RAM is
being used and puts the AD9954 into an automatic profile loop
sequence that allows the user to implement a frequency/phase
composite sweep that runs without external inputs. See the
Internal Profile Control section for more details.
CFR1<26>: Load Amplitude Ramp Rate Control Bit
CFR1<26> = 0 (default). The amplitude ramp rate timer is
loaded only upon timeout (timer == 1); it is not loaded due to
an I/O update input signal.
CFR1<26> = 1. The amplitude ramp rate timer is loaded upon
either timeout (timer == 1) or at the time of an I/O update
input signal.
CFR1<25>: Shaped On-Off Keying Enable Bit
CFR1<25> = 0 (default). Shaped on-off keying is bypassed.
CFR1<25> = 1. Shaped on-off keying is enabled. See also
CFR1<24>.
CFR1<24>: Autoshaped On-Off Keying Enable Bit
If CFR1<25> is cleared, CFR1<24> is ignored.
CFR1<24> = 0 (default). Manual shaped on-off keying
operation. See the Shaped On-Off Keying section for details.
CFR1<24> = 1. Autoshaped on-off keying operation. See the
Shaped On-Off Keying section for details.
CFR1<23>: Automatic Synchronization Enable Bit
CFR1<23> = 0 (default). The automatic synchronization feature
of multiple AD9954s is inactive.
CFR1<23> = 1. The automatic synchronization feature of
multiple AD9954s is active. See the Synchronizing Multiple
AD9954s section for details.
CFR1<22>: Software Manual Synchronization of Multiple
AD9954s
CFR1<22> = 0 (default). The manual synchronization feature is
inactive.
CFR1<22> = 1. The software-controlled manual synchronization
feature is executed. The SYNC_CLK rising edge is advanced by
one SYNC_CLK cycle, and this bit is autocleared. To advance
the rising edge multiple times, this bit needs to be set once for
each advance.
CFR1<21>: Linear Frequency Sweep Enable
CFR1<21> = 0 (default). The linear frequency sweep capability
of the AD9954 is inactive.
CFR1<21> = 1. The linear frequency sweep capability of the
AD9954 is enabled. See the Linear Sweep Mode section for details.
CFR1<20:16>: Not Used, Leave Clear
CFR1<15>: Linear Sweep Ramp Rate Load Control Bit
CFR1<15> = 0 (default). The linear sweep ramp rate timer is
loaded only upon timeout (timer == 1); it is not loaded due to
an I/O update input signal.
CFR1<15> = 1. The linear sweep ramp rate timer is loaded
either upon timeout (timer == 1) or at the time of an I/O
update input signal.
CFR1<14>: Autoclear Frequency Accumulator Bit
CFR1<14> = 0 (default). The current state of the frequency
accumulator is not impacted by receipt of an I/O update signal.
CFR1<14> = 1. The frequency accumulator is automatically and
synchronously cleared for one cycle upon receipt of an I/O
UPDATE signal.
CFR1<13>: Autoclear Phase Accumulator Bit
CFR1<13> = 0 (default). The current state of the phase
accumulator is not impacted by receipt of an I/O update signal.
CFR1<13> = 1. The phase accumulator is automatically and
synchronously cleared for one cycle upon receipt of an I/O
update signal.
CFR1<12>: Sine/Cosine Select Bit
CFR1<12> = 0 (default). The angle-to-amplitude conversion
logic employs a cosine function.
CFR1<12> = 1. The angle-to-amplitude conversion logic
employs a sine function.
CFR1<11>: Clear Frequency Accumulator
CFR1<11> = 0 (default). The frequency accumulator functions
as normal.
CFR1<11> = 1. The frequency accumulator memory elements
are cleared and held clear until this bit is cleared.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9911BCPZ | IC DDS 500MSPS DAC 10BIT 56LFCSP |
| VE-B11-IY-F4 | CONVERTER MOD DC/DC 12V 50W |
| VE-B11-IY-F1 | CONVERTER MOD DC/DC 12V 50W |
| VE-2WZ-IY-F4 | CONVERTER MOD DC/DC 2V 20W |
| VE-2WZ-IY-F1 | CONVERTER MOD DC/DC 2V 20W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9954YSVZ | 制造商:Analog Devices 功能描述:IC DDS 400MSPS SMD 9954 TQFP48 |
| AD9954YSVZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:400 MSPS, 14-Bit, 1.8 V CMOS, Direct Digital Synthesizer |
| AD9954YSVZ-REEL7 | 功能描述:IC DDS DAC 14BIT 1.8V 48TQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 調節字寬（位）:32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD9954YSVZ-REEL71 | 制造商:AD 制造商全稱:Analog Devices 功能描述:400 MSPS, 14-Bit, 1.8 V CMOS, Direct Digital Synthesizer |
| AD9955KS6 | 制造商:AD 功能描述:* |
發布緊急采購，3分鐘左右您將得到回復。