- 您現在的位置：買賣IC網 > PDF目錄1984 > AD7851ANZ (Analog Devices Inc)IC ADC 14BIT SRL 333KSPS 24-DIP PDF資料下載
參數資料
| 型號： | AD7851ANZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 2/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 14BIT SRL 333KSPS 24-DIP |
| 產品變化通告： | Product Discontinuance 27/Oct/2011 |
| 標準包裝： | 15 |
| 位數： | 14 |
| 采樣率（每秒）： | 333k |
| 數據接口： | 8051，QSPI?，串行，SPI? µP |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 89.25mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 24-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 24-PDIP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個偽差分，單極；1 個偽差分，雙極 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
AD7851
–10–
REV. B
AD7851 ON-CHIP REGISTERS
The AD7851 powers up with a set of default conditions, and the user need not ever write to the device. In this case, the AD7851 will
operate as a read-only ADC. The AD7851 still retains the flexibility for performing a full power-down and a full self-calibration.
Note that the DIN pin should be tied to DGND for operating the AD7851 as a read-only ADC.
Extra features and flexibility, such as performing different power-down options, different types of calibrations, including system cali-
bration, and software conversion starts can be selected by writing to the part.
The AD7851 contains a control register, ADC output data register, status register, test register, and 10 calibration registers.
The control register is write-only, the ADC output data register and the status register are read-only, and the test and calibration
registers are both read/write registers. The test register is used for testing the part and should not be written to.
Addressing the On-Chip Registers
Writing
A write operation to the AD7851 consists of 16 bits. The two MSBs, ADDR0 and ADDR1, are decoded to determine which regis-
ter is addressed, and the subsequent 14 bits of data are written to the addressed register. It is not until all 16 bits are written that
the data is latched into the addressed register. Table I shows the decoding of the address bits, while Figure 4 shows the overall
write register hierarchy.
Table I. Write Register Addressing
ADDR1
ADDR0
Comment
00
This combination does not address any register so the subsequent 14 data bits are ignored.
01
This combination addresses the TEST REGISTER. The subsequent 14 data bits are written to the test register.
10
This combination addresses the CALIBRATION REGISTERS. The subsequent 14 data bits are written
to the selected calibration register.
11
This combination addresses the CONTROL REGISTER. The subsequent 14 data bits are written to the
control register.
Reading
To read from the various registers the user must first write to Bits 6 and 7 in the Control Register, RDSLT0 and RDSLT1. These
bits are decoded to determine which register is addressed during a read operation. Table II shows the decoding of the read address
bits while Figure 5 shows the overall read register hierarchy. The power-up status of these bits is 00 so that the default read will be
from the ADC output data register.
Once the read selection bits are set in the control register, all subsequent read operations that follow will be from the selected register
until the read selection bits are changed in the control register.
Table II. Read Register Addressing
RDSLT1
RDSLT0
Comment
00
All successive read operations will be from ADC OUTPUT DATA REGISTER. This is the power-up default
setting. There will always be two leading zeros when reading from the ADC output data register.
01All successive read operations will be from TEST REGISTER.
10All successive read operations will be from CALIBRATION REGISTERS.
11All successive read operations will be from STATUS REGISTER.
ADDR1, ADDR0
DECODE
TEST
REGISTER
CONTROL
REGISTER
GAIN (1)
OFFSET (1)
DAC (8)
GAIN (1)
OFFSET (1)
GAIN (1)
01
10
11
00
01
10
11
CALSLT1, CALSLT0
DECODE
CALIBRATION
REGISTERS
Figure 4. Write Register Hierarchy/Address Decoding
RDSLT1, RDSLT0
DECODE
TEST
REGISTER
CALIBRATION
REGISTERS
STATUS
REGISTER
GAIN (1)
OFFSET (1)
DAC (8)
GAIN (1)
OFFSET (1)
GAIN (1)
01
10
11
00
01
10
11
CALSLT1, CALSLT0
DECODE
ADC OUTPUT
DATA REGISTER
00
Figure 5. Read Register Hierarchy/Address Decoding
相關PDF資料 |
PDF描述 |
|---|---|
| AD7853BNZ | IC ADC 12BIT SRL 200KSPS 24-DIP |
| AD7854BRZ | IC ADC 12BIT PARALLEL LP 28-SOIC |
| AD7856ARZ-REEL7 | IC ADC 14BIT 8CHAN 5V 24SOIC |
| AD7858LBNZ | IC ADC 12BIT 8CHAN SRL 24DIP |
| AD7859BSZ | IC ADC 12BIT 8CHAN LP 44-MQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7851AR | 制造商:Analog Devices 功能描述:ADC Single SAR 333ksps 14-bit Serial 24-Pin SOIC W 制造商:Rochester Electronics LLC 功能描述:14 BIT SELF CALIBRATION ADC I.C. - Bulk |
| AD7851AR-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 333ksps 14-bit Serial 24-Pin SOIC W T/R |
| AD7851ARS | 制造商:Analog Devices 功能描述:ADC Single SAR 333ksps 14-bit Serial 24-Pin SSOP 制造商:Analog Devices 功能描述:IC 14-BIT ADC |
| AD7851ARS-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 333ksps 14-bit Serial 24-Pin SSOP T/R |
| AD7851ARSZ | 功能描述:IC ADC 14BIT SRL 333KSPS 24SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。