參數資料
型號： 28F640P3
廠商： Intel Corp.
英文描述： Intel StrataFlash Embedded Memory
中文描述： 英特爾StrataFlash嵌入式存儲器
文件頁數： 30/82頁
文件大?。?/td> 749K
代理商： 28F640P3
28F6408W30, 28F3204W30, 28F320W30, 28F640W30
24
Preliminary
4.5.1
Clear Status Register
To clear the status register, execute the Clear Status Register command. When the status register is
cleared, only bits 1, 3, 4, and 5 are cleared. A status register bit is considered set if its value is a one
(1) and cleared if its value is a zero (0). Since bits 0, 2, 6 and 7 indicated different error conditions
and/or device states, these bits can only be set and cleared by the WSM and are not cleared when a
Clear Status Register command is given. The status register should be cleared before implementing
any program or erase operations. After executing the Clear Status Register command, the device
returns to read array mode. A device reset also clears the status register.
4.6
Read-While-Write/Erase
1.8 Volt Intel
Wireless Flash Memory supports a new flash multi-partition architecture. By
dividing the flash memory into many separate partitions, the device is capable of reading from one
partition while programing or erasing in another partition; hence the terms, Read-While-Write
(RWW) and Read-While-Erase (RWE). These features greatly enhance flash data storage
performance.
To perform a RWW operation, execute the Word Program command to one partition. While this
operation is being performed by the flash WSM, execute the Read Array command to another
partition.
To perform a RWE operation, execute the Block Erase command to one partition. While this
operation is being performed by the flash WSM, execute the Read Array command to another
partition.
1.8 Volt Intel
Wireless Flash Memory does not support simultaneous program and erase operations.
Attempting to perform operations such as these will result in a command sequence error. Only one
partition may be programming or erasing while another is reading.
5.0
Program and Erase Voltages
The 1.8 Volt Intel
Wireless Flash Memory with 3 Volt I/O and SRAM memory provides in-
system program and erase at V
PP1
. For factory programming, it also includes a low-cost,
backward-compatible 12 V programming feature. It also includes an Enhanced Factory
Programming (EFP) feature.
5.1
Factory Program Mode
The standard factory programming mode uses the same commands and algorithm as the Word
Program mode (40h/10h). When V
PP
is at V
PP1
, program and erase currents are drawn through the
V
CC
pin. Note that if V
PP
is driven by a logic signal, V
PP1
must remain above the V
PP1
Min value to
perform in-system flash modifications. When V
PP
is connected to a 12 V power supply, the device
draws program and erase current directly from the V
PP
pin. This eliminates the need for an external
switching transistor to control the V
PP
voltage.
Figure 9,
“
Example of V
PP
Power Supply
Configurations
shows examples of flash power supply usage in various configurations.
相關PDF資料
PDF描述
28F320C3 3 Volt Advanced Boot Block Flash Memory(3 V 高級快速引導塊閃速存儲器)
28F800C3 3 Volt Advanced Boot Block Flash Memory(3 V 高級快速引導塊閃速存儲器)
28F160C3 3 Volt Advanced Boot Block Flash Memory(3 V 高級快速引導塊閃速存儲器)
28F320D18 1.8 Volt Intel Dual-Plane Flash Memory(1.8 V Intel 雙平面閃速存儲器)
28F320J5 5 Volt Intel StrataFlash Memory(5 V 32M位英特爾StrataFlash存儲器)
相關代理商/技術參數
參數描述
28F640W30 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:1.8 Volt Intel Wireless Flash Memory with 3 Volt I/O and SRAM (W30)
28F650 制造商:Cinch Connectors 功能描述:1 Lug Terminal Strip
28F651 制造商:Cinch Connectors 功能描述:2 Lug Terminal Strip
28F652 制造商:Cinch Connectors 功能描述:3 Lug Terminal Strip
28F653 制造商:Cinch Connectors 功能描述:4 Lug Terminal Strip
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*