- 您現在的位置：買賣IC網 > PDF目錄371435 > 28F160C2 (Intel Corp.) 2.4V Advanced+ Boot Block Flash Memory(2.4V高級引導塊閃速存儲器) PDF資料下載
參數資料
| 型號： | 28F160C2 |
| 廠商： | Intel Corp. |
| 英文描述： | 2.4V Advanced+ Boot Block Flash Memory(2.4V高級引導塊閃速存儲器) |
| 中文描述： | 2.4V的高級啟動塊閃存（2.4V的高級引導塊閃速存儲器） |
| 文件頁數： | 20/56頁 |
| 文件大?。?/td> | 283K |
| 代理商： | 28F160C2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
28F800C2, 28F160C2
E
20
PRELIMINARY
Table 9. Block Locking State Transitions
Current State
Erase/Prog
Lock Command Input Result [Next State]
WP#
DQ
1
DQ
0
Name
Allowed
Lock
Unlock
Lock-Down
0
0
0
“Unlocked”
Yes
Goes To [001]
No Change
Goes To [011]
0
0
1
“Locked” (Default)
No
No Change
Goes To [000] Goes To [011]
0
1
1
“Locked-Down”
No
No Change
No Change
No Change
1
0
0
“Unlocked”
Yes
Goes To [101]
No Change
Goes To [111]
1
0
1
“Locked”
No
No Change
Goes To [100] Goes To [111]
1
1
0
Lock-Down Disabled
Yes
Goes To [111]
No Change
Goes To [111]
1
1
1
Lock-Down Disabled
No
No Change
Goes To [110]
No Change
NOTES:
1.
In this table, the notation [XYZ] denotes the locking state of a block, where X = WP#, Y = DQ
, and Z = DQ
. The current
locking state of a block is defined by the state of WP# and the two bits of the block lock status (DQ
0
, DQ
1
). DQ
0
indicates if
a block is locked (1) or unlocked (0). DQ
1
indicates if a block has been locked-down (1) or not (0).
At power-up or device reset, all blocks default to Locked state [001] (if WP# = 0). Holding WP# = 0 is the recommended
default.
The
“Erase/Program Allowed” column shows whether erase and program operations are enabled (Yes) or disabled (No)
in that block’s current locking state.
The “Lock Command Input Result [Next State]” column shows the result of writing the three locking commands (Lock,
Unlock, Lock-Down) in the current locking state. For example, “Goes To [001]” would mean that writing the command to a
block in the current locking state would change it to [001].
2.
3.
4.
3.4
128-Bit Protection Register
The Advanced+ Boot Block architecture includes a
128-bit protection register than can be used to
increase the security of a system design. For
example, the number contained in the protection
register can be used to
“mate” the flash component
with other system components such as the CPU or
ASIC, preventing device substitution. Additional
application information can be found in Intel
application note
AP-657
Designing with the
Advanced+ Boot Block Flash Memory Architecture
.
The 128-bits of the protection register are divided
into two 64-bit segments. One of the segments is
programmed at the Intel factory with a unique 64-bit
number, which is unchangeable. The other segment
is left blank for customer designs to program as
desired.
Once
the
programmed, it can be locked to prevent
reprogramming.
customer
segment
is
3.4.1
READING THE PROTECTION
REGISTER
The protection register is read in the configuration
read mode. The device is switched to this mode by
writing the Read Configuration command (90H).
Once in this mode, read cycles from addresses
shown in Appendix G retrieve the specified
information. To return to read array mode, write the
Read Array command (FFH).
3.4.2
PROGRAMMING THE PROTECTION
REGISTER
The protection register bits are programmed using
the two-cycle Protection Program command. The
64-bit number is programmed 16 bits at a time for
word-wide parts and eight bits at a time for byte-
wide parts. First write the Protection Program Setup
command, C0H. The next write to the device will
latch in address and data and program the specified
location. The allowable addresses are shown in
Appendix G. See Figure 15 for the
Protection
Register Programming Flowchart
.
相關PDF資料 |
PDF描述 |
|---|---|
| 28F800C2 | 2.4V Advanced+ Boot Block Flash Memory(2.4V高級引導塊閃速存儲器) |
| 28F160S3 | 3 V FlashFile Memory(3 V FlashFile 存儲器) |
| 28F320S3 | 3 V、32MB FlashFile Memory(3 V、32M位FlashFile 存儲器) |
| 28F160S5 | 5 V FlashFile Memory(5 V FlashFile 存儲器) |
| 28F320S5 | 3 V、32MB FlashFile Memory(3 V、32M位FlashFile 存儲器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 28F160C3 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:3 Volt Intel Advanced+ Boot Block Flash Memory |
| 28F160C3BA90 | 制造商: 功能描述: 制造商:Intel 功能描述: 制造商:undefined 功能描述: |
| 28F160C3TD70 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 28F160F3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FAST BOOT BLOCK FLASH MEMORY FAMILY 8 AND 16 MBIT |
| 28F160F3B95 | 制造商:Intel 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。