- 您現在的位置：買賣IC網 > PDF目錄371435 > 28F160C2 (Intel Corp.) 2.4V Advanced+ Boot Block Flash Memory(2.4V高級引導塊閃速存儲器) PDF資料下載
參數資料
| 型號： | 28F160C2 |
| 廠商： | Intel Corp. |
| 英文描述： | 2.4V Advanced+ Boot Block Flash Memory(2.4V高級引導塊閃速存儲器) |
| 中文描述： | 2.4V的高級啟動塊閃存（2.4V的高級引導塊閃速存儲器） |
| 文件頁數： | 10/56頁 |
| 文件大小： | 283K |
| 代理商： | 28F160C2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
28F800C2, 28F160C2
E
10
PRELIMINARY
3.0
PRINCIPLES OF OPERATION
The 2.4 Volt Advanced+ Boot Block flash memory
family utilizes a CUI and automated algorithms to
simplify program and erase operations. The CUI
allows for 100% CMOS-evel control inputs and
fixed
power
supplies
programming.
during
erasure
and
The internal WSM completely automates program
and erase operations while the CUI signals the start
of an operation and the status register reports
status. The CUI handles the WE# interface to the
data and address latches, as well as system status
requests during WSM operation.
3.1
Bus Operation
The 2.4 Volt Advanced+ Boot Block flash memory
devices read, program and erase in-system via the
local CPU or microcontroller. All bus cycles to or
from the flash memory conform to standard
microcontroller bus cycles. Four control pins dictate
the data flow in and out of the flash component:
CE#, OE#, WE# and RP#. These bus operations
are summarized in Table 3.
3.1.1
READ
The flash memory has four read modes available:
read array, read configuration, read status and read
query. These modes are accessible independent of
the V
voltage. The appropriate read mode
command must be issued to the CUI to enter the
corresponding mode. Upon initial device power-up
or after exit from reset, the device automatically
defaults to read array mode.
CE# and OE# must be driven active to obtain data
at the outputs. CE# is the device selection control;
when active it enables the flash memory device.
OE# is the data output control and it drives the
selected memory data onto the I/O bus. For all read
modes, WE# and RP# must be at V
IH
. Figure 7
illustrates a read cycle.
3.1.2
OUTPUT DISABLE
With OE# at a logic-high level (V
), the device
outputs are disabled. Output pins are placed in a
high-mpedance state.
3.1.3
STANDBY
Deselecting the device by bringing CE# to a logic-
high level (V
) places the device in standby mode,
which
substantially
reduces
consumption without any latency for subsequent
read accesses. In standby, outputs are placed in a
high-impedance state independent of OE#. If
deselected during program or erase operation, the
device continues to consume active power until the
program or erase operation is complete.
device
power
Table 3. Bus Operations
(1)
Mode
Note
RP#
CE#
OE#
WE#
DQ
0
–7
DQ
8-15
Read (Array, Status,
Configuration, or Query)
2-4
V
IH
V
IL
V
IL
V
IH
D
OUT
D
OUT
Output Disable
2
V
IH
V
IL
V
IH
V
IH
High Z
High Z
Standby
2
V
IH
V
IH
X
X
High Z
High Z
Reset
2,7
V
IL
X
X
X
High Z
High Z
Write
2,5-7
V
IH
V
IL
V
IH
V
IL
D
IN
D
IN
NOTES:
1.
2.
3.
4.
5.
6.
7.
8-bit devices use only DQ [0:7], 16-bit devices use DQ [0:15]
X must be V
IL
, V
IH
for control pins and addresses.
See DC Characteristicsfor V
PPLK
, V
PP1
, V
PP2
, V
PP3
, voltages.
Manufacturer and device codes may also be accessed in read configuration mode (A
1
–A
20
= 0). See Table 4.
Refer to Table 5 for valid D
IN
during a write operation.
To program or erase the lockable blocks, hold WP# at V
IH
.
RP# must be at GND
±
0.2 V to meet the maximum deep power-down current specified.
相關PDF資料 |
PDF描述 |
|---|---|
| 28F800C2 | 2.4V Advanced+ Boot Block Flash Memory(2.4V高級引導塊閃速存儲器) |
| 28F160S3 | 3 V FlashFile Memory(3 V FlashFile 存儲器) |
| 28F320S3 | 3 V、32MB FlashFile Memory(3 V、32M位FlashFile 存儲器) |
| 28F160S5 | 5 V FlashFile Memory(5 V FlashFile 存儲器) |
| 28F320S5 | 3 V、32MB FlashFile Memory(3 V、32M位FlashFile 存儲器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 28F160C3 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:3 Volt Intel Advanced+ Boot Block Flash Memory |
| 28F160C3BA90 | 制造商: 功能描述: 制造商:Intel 功能描述: 制造商:undefined 功能描述: |
| 28F160C3TD70 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 28F160F3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FAST BOOT BLOCK FLASH MEMORY FAMILY 8 AND 16 MBIT |
| 28F160F3B95 | 制造商:Intel 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。