參數資料
型號： 24C02SC
廠商： Microchip Technology Inc.
英文描述： 2K 5.0V IIC serial EEPROMs(2.5V~5.5V,2K位,1M次擦寫周期,ISO7816標準)
中文描述： 2K 5.0V國際進口電壓（2.5V?5.5V的和2K位，100萬次擦寫周期，符合ISO7816標準串行EEPROM）
文件頁數： 85/170頁
文件大小： 4191K
代理商： 24C02SC
2003 Microchip Technology Inc.
Preliminary
DS40300C-page 83
PIC16F62X
12.4.2
USART SYNCHRONOUS MASTER
RECEPTION
Once Synchronous mode is selected, reception is
enabled
by
setting
either
(RCSTA<5>) or enable bit CREN (RCSTA<4>). Data is
sampled on the RB1/RX/DT pin on the falling edge of
the clock. If enable bit SREN is set, then only a single
word is received. If enable bit CREN is set, the recep-
tion is continuous until CREN is cleared. If both bits are
set, then CREN takes precedence. After clocking the
last bit, the received data in the Receive Shift Register
(RSR) is transferred to the RCREG register (if it is
empty). When the transfer is complete, interrupt flag bit
RCIF (PIR1<5>) is set. The actual interrupt can be
enabled/disabled by setting/clearing enable bit RCIE
(PIE1<5>). Flag bit RCIF is a read only bit which is
RESET by the hardware. In this case, it is RESET
when the RCREG register has been read and is empty.
The RCREG is a double buffered register (i.e., it is a
two-deep FIFO). It is possible for two bytes of data to
be received and transferred to the RCREG FIFO and a
third byte to begin shifting into the RSR register. On the
clocking of the last bit of the third byte, if the RCREG
register is still full then overrun error bit OERR
(RCSTA<1>) is set. The word in the RSR will be lost.
The RCREG register can be read twice to retrieve the
two bytes in the FIFO. Bit OERR has to be cleared in
software (by clearing bit CREN). If bit OERR is set,
transfers from the RSR to the RCREG are inhibited, so
it is essential to clear bit OERR if it is set. The 9th
enable
bit
SREN
receive bit is buffered the same way as the receive
data. Reading the RCREG register, will load bit RX9D
with a new value, therefore it is essential for the user to
read the RCSTA register before reading RCREG in
order not to lose the old RX9D information.
Steps to follow when setting up a Synchronous Master
Reception:
1.
Initialize the SPBRG register for the appropriate
baud rate. (Section 12.1)
2.
Enable the synchronous master serial port by
setting bits SYNC, SPEN, and CSRC.
3.
Ensure bits CREN and SREN are clear.
4.
If interrupts are desired, then set enable bit
RCIE.
5.
If 9-bit reception is desired, then set bit RX9.
6.
If a single reception is required, set bit SREN.
For continuous reception set bit CREN.
7.
Interrupt flag bit RCIF will be set when reception
is complete and an interrupt will be generated if
enable bit RCIE was set.
8.
Read the RCSTA register to get the ninth bit (if
enabled) and determine if any error occurred
during reception.
9.
Read the 8-bit received data by reading the
RCREG register.
10. If any error occurred, clear the error by clearing
bit CREN.
TABLE 12-10: REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on:
POR
Value on all
other
RESETS
0Ch
PIR1
EEIF
CMIF
RCIF
TXIF
—
CCP1IF TMR2IF
TMR1IF
0000 -000
RX9D
0000 -00x
0000 0000
0000 -000
0000 -00x
0000 0000
-000 -000
0000 -010
0000 0000
18h
RCSTA
SPEN
RX9
SREN CREN
ADEN
FERR
OERR
1Ah
RCREG USART Receive Register
8Ch
PIE1
EEPIE
CMIE
RCIE
TXIE
—
CCP1IE TMR2IE TMR1IE
-000 0000
BRGH
TRMT
98h
TXSTA
CSRC
TX9
TXEN
SYNC
—
TX9D
0000 -010
0000 0000
99h
Legend:
x
= unknown,
-
= unimplemented read as '0'. Shaded cells are not used for Synchronous Master Reception.
SPBRG Baud Rate Generator Register
相關PDF資料
PDF描述
24C02A 2K 5.0V CMOS serial EEPROMs(2K位,5.0V,IIC串行EEPROM)
24C02C 2K 5.0V IIC serial EEPROMs(2K位，1M次擦寫周期，硬件寫保護，二線串行接口,EEPROM)
24C02C-EP 2K 5.0V I 2 C ⑩ Serial EEPROM
24C02C-ESN 2K 5.0V I 2 C ⑩ Serial EEPROM
24C02C-EST 2K 5.0V I 2 C ⑩ Serial EEPROM
相關代理商/技術參數
參數描述
24C02SC/S 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SERIAL EEPROM|256X8|CMOS|DIE
24C02SC-/S 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1K/2K 5.0V I2C Serial EEPROMs for Smart Cards
24C02SC/S08 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SERIAL EEPROM|256X8|CMOS|DIE
24C02SC-/S08 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1K/2K 5.0V I2C Serial EEPROMs for Smart Cards
24C02SC/W 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SERIAL EEPROM|256X8|CMOS|WAFER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*