- 您現在的位置：買賣IC網 > PDF目錄371394 > 24C02SC (Microchip Technology Inc.) 2K 5.0V IIC serial EEPROMs(2.5V~5.5V,2K位,1M次擦寫周期,ISO7816標準) PDF資料下載
參數資料
| 型號： | 24C02SC |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 2K 5.0V IIC serial EEPROMs(2.5V~5.5V,2K位,1M次擦寫周期,ISO7816標準) |
| 中文描述： | 2K 5.0V國際進口電壓（2.5V?5.5V的和2K位，100萬次擦寫周期，符合ISO7816標準串行EEPROM） |
| 文件頁數： | 59/170頁 |
| 文件大?。?/td> | 4191K |
| 代理商： | 24C02SC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁當前第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁
2003 Microchip Technology Inc.
Preliminary
DS40300C-page 57
PIC16F62X
9.6
Comparator Interrupts
The Comparator Interrupt flag is set whenever there is
a change in the output value of either comparator.
Software will need to maintain information about the
status of the output bits, as read from CMCON<7:6>, to
determine the actual change that has occurred. The
CMIF bit, PIR1<6>, is the Comparator Interrupt Flag.
The CMIF bit must be RESET by clearing ‘0’. Since it is
also possible to write a '1' to this register, a simulated
interrupt may be initiated.
The CMIE bit (PIE1<6>) and the PEIE bit
(INTCON<6>) must be set to enable the interrupt. In
addition, the GIE bit must also be set. If any of these
bits are clear, the interrupt is not enabled, though the
CMIF bit will still be set if an interrupt condition occurs.
The user, in the interrupt service routine, can clear the
interrupt in the following manner:
a)
Any write or read of CMCON. This will end the
mismatch condition.
b)
Clear flag bit CMIF.
A mismatch condition will continue to set flag bit CMIF.
Reading CMCON will end the mismatch condition, and
allow flag bit CMIF to be cleared.
9.7
Comparator Operation During
SLEEP
When a comparator is active and the device is placed
in SLEEP mode, the comparator remains active and
the interrupt is functional if enabled. This interrupt will
wake-up the device from SLEEP mode when enabled.
While the comparator is powered-up, higher SLEEP
currents than shown in the power-down current
specification will occur. Each comparator that is
operational will consume additional current as shown in
the comparator specifications. To minimize power
consumption while in SLEEP mode, turn off the
comparators, CM<2:0> = 111, before entering SLEEP.
If the device wakes-up from SLEEP, the contents of the
CMCON register are not affected.
9.8
Effects of a RESET
A device RESET forces the CMCON register to its
RESET state. This forces the Comparator module to be
in the comparator RESET mode, CM2:CM0 = 000.
This ensures that all potential inputs are analog inputs.
Device current is minimized when analog inputs are
present at RESET time. The comparators will be
powered-down during the RESET interval.
9.9
Analog Input Connection
Considerations
A simplified circuit for an analog input is shown in
Figure 9-4. Since the analog pins are connected to a
digital output, they have reverse biased diodes to V
DD
and V
SS
. The analog input therefore, must be between
V
SS
and V
DD
. If the input voltage deviates from this
range by more than 0.6V in either direction, one of the
diodes is forward biased and a latchup may occur. A
maximum
source
impedance
recommended for the analog sources. Any external
component connected to an analog input pin, such as
a capacitor or a Zener diode, should have very little
leakage current.
of
10 k
is
Note:
If a change in the CMCON register
(C1OUT or C2OUT) should occur when a
read operation is being executed (start of
the Q2 cycle), then the CMIF (PIR1<6>)
interrupt flag may not get set.
相關PDF資料 |
PDF描述 |
|---|---|
| 24C02A | 2K 5.0V CMOS serial EEPROMs(2K位,5.0V,IIC串行EEPROM) |
| 24C02C | 2K 5.0V IIC serial EEPROMs(2K位，1M次擦寫周期，硬件寫保護，二線串行接口,EEPROM) |
| 24C02C-EP | 2K 5.0V I 2 C ⑩ Serial EEPROM |
| 24C02C-ESN | 2K 5.0V I 2 C ⑩ Serial EEPROM |
| 24C02C-EST | 2K 5.0V I 2 C ⑩ Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 24C02SC/S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SERIAL EEPROM|256X8|CMOS|DIE |
| 24C02SC-/S | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1K/2K 5.0V I2C Serial EEPROMs for Smart Cards |
| 24C02SC/S08 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SERIAL EEPROM|256X8|CMOS|DIE |
| 24C02SC-/S08 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1K/2K 5.0V I2C Serial EEPROMs for Smart Cards |
| 24C02SC/W | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SERIAL EEPROM|256X8|CMOS|WAFER |
發布緊急采購，3分鐘左右您將得到回復。