- 您現在的位置：買賣IC網 > PDF目錄373785 > ZL50015GAC (ZARLINK SEMICONDUCTOR INC) Enhanced 1 K Digital Switch with Stratum 4E DPLL PDF資料下載
參數資料
| 型號： | ZL50015GAC |
| 廠商： | ZARLINK SEMICONDUCTOR INC |
| 元件分類： | 路由/交換 |
| 英文描述： | Enhanced 1 K Digital Switch with Stratum 4E DPLL |
| 中文描述： | TELECOM, DIGITAL TIME SWITCH, PBGA256 |
| 封裝： | 17 X 17 MM, 1.61 MM HEIGHT, PLASTIC, MS-034, BGA-256 |
| 文件頁數： | 36/122頁 |
| 文件大小： | 926K |
| 代理商： | ZL50015GAC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁
ZL50015
Data Sheet
36
Zarlink Semiconductor Inc.
10.0 Connection Memory Block Programming
This feature allows for fast initialization of the connection memory after power up.
10.1 Memory Block Programming Procedure
1. Set MBPE (bit 3) in the Control Register (CR) from low to high.
2. Configure BPD2 - 0 (bits 3 - 1) in the Internal Mode Selection (IMS) register to the desired values to be loaded
into CM_L.
3. Start the block programming by setting MBPS (bit 0) in the Internal Mode Selection Register (IMS) high. The val-
ues stored in BPD2 - 0 will be loaded into bits 2 - 0 of all CM_L positions. The remaining CM_L locations (bits 15
- 3) and the programmable values in the CM_H (bits 4 - 0) will be loaded with zero values.
The following tables show the resulting values that are in the CM_L and CM_H connection memory locations.
Note: Bits 15 to 5 are reserved in Connection Memory High and should always be 0.
It takes at least two frame periods (250
μ
s) to complete a block program cycle.
MBPS (bit 0) in the Control Register (CR) will automatically reset to a low position after the block programming
process has completed.
MBPE (bit 3) in the Internal Mode Selection (IMS) register must be cleared from high to low to terminate the block
programming process. This is not an automatic action taken by the device and must be performed manually.
Note
: Once the block program has been initiated, it can be terminated at any time prior to completion by setting
MBPS (bit 0) in the Control Register (CR) or MBPE (bit 3) in the Internal Mode Selection (IMS) register to low. If the
MBPE bit was used to terminate the block programming, the MBPS bit will have to be set low before enabling other
device operations.
11.0 Device Operation in Master Mode and Slave Modes
This device has two main operating modes - Master mode and Slave mode. Each operating mode has different
input/output clock and frame pulse setup requirements and usage.
If the device is programmed to work in Master mode, it is expected that the input clock and frame pulse will be
supplied from the embedded DPLL, either directly using the internal loopback mode or indirectly through external
loopback path. Sources and destinations of the device’s serial input and output data, respectively, have to be
synchronized with the device’s output clock and frame pulse. In Master mode, output clocks and frame pulses are
driven by the DPLL and they are always available with any of the specified frequencies.
The device can also operate in two different Slave modes: Divided Slave mode and Multiplied Slave mode. In either
Slave modes, output clocks and frame pulses are generated based on CKi and FPi. The difference is that, in
Divided Slave mode, the output clocks and frame pulses are directly divided from CKi/FPi, while in Multiplied Slave
mode, the output clocks and frame pulses are generated from an internal high-speed clock synchronized to CKi
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Value
0
0
0
0
0
0
0
0
0
0
0
0
0
BPD2
BPD1
BPD0
Table 5 - Connection Memory Low After Block Programming
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Value
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 6 - Connection Memory High After Block Programming
相關PDF資料 |
PDF描述 |
|---|---|
| ZL50015QCC | Enhanced 1 K Digital Switch with Stratum 4E DPLL |
| ZL50015QCC1 | Enhanced 1 K Digital Switch with Stratum 4E DPLL |
| ZL50018 | 2 K Digital Switch with Enhanced Stratum 3 DPLL |
| ZL50018GAC | 2 K Digital Switch with Enhanced Stratum 3 DPLL |
| ZL50018QCC | 2 K Digital Switch with Enhanced Stratum 3 DPLL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ZL50015GAG2 | 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 1K X 1K 1.8V/3.3V 256BGA - Trays 制造商:Zarlink Semiconductor Inc 功能描述:SWIT FABRIC 1K X 1K 1.8V/3.3V 256BGA - Trays |
| ZL50015QCC | 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 1K X 1K 1.8V/3.3V 256LQFP - Trays |
| ZL50015QCC1 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Enhanced 1 K Digital Switch with Stratum 4E DPLL |
| ZL50015QCG1 | 制造商:Microsemi Corporation 功能描述: 制造商:Microsemi Corporation 功能描述:PB FREE 1K+RATE CONVERSION AND S4E DPLL 制造商:Microsemi Corporation 功能描述:PB FREE 1K+RATE CONVERSION AND S4E DPLL - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TDM SWITCH 1K-CH ENH 256LQFP 制造商:Microsemi Corporation 功能描述:IC TDM SWITCH 1K-CH ENH 256LQFP |
| ZL50016 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Enhanced 1 K Digital Switch |
發布緊急采購，3分鐘左右您將得到回復。