參數資料
型號: ZL30101QDG1
廠商: ZARLINK SEMICONDUCTOR INC
元件分類: 通信及網絡
英文描述: T1/E1 Stratum 3 System Synchronizer
中文描述: SPECIALTY TELECOM CIRCUIT, PQFP64
封裝: 10 X 10 MM, 1 MM HEIGHT, LEAD FREE, MS-026ACD, TQFP-64
文件頁數: 21/35頁
文件大小: 328K
代理商: ZL30101QDG1
ZL30101
Data Sheet
21
Zarlink Semiconductor Inc.
Figure 10 - Reference Switching in Normal Mode
5.0 Measures of Performance
The following are some PLL performance indicators and their corresponding definitions.
5.1 Jitter
Timing jitter is defined as the high frequency variation of the clock edges from their ideal positions in time. Wander
is defined as the low-frequency variation of the clock edges from their ideal positions in time. High and low
frequency variation imply phase oscillation frequencies relative to some demarcation frequency. (Often 10 Hz or
20 Hz for DS1 or E1, higher for SONET/SDH clocks.) Jitter parameters given in this data sheet are total timing jitter
numbers, not cycle-to-cycle jitter.
5.2 Jitter Generation (Intrinsic Jitter)
Generated jitter is the jitter produced by the PLL and is measured at its output. It is measured by applying a
reference signal with no jitter to the input of the device, and measuring its output jitter. Generated jitter may also be
measured when the device is in a non-synchronizing mode, such as free running or holdover, by measuring the
output jitter of the device. Generated jitter is usually measured with various bandlimiting filters depending on the
applicable standards.
5.3 Jitter Tolerance
Jitter tolerance is a measure of the ability of a PLL to operate properly (i.e., remain in lock and or regain lock in the
presence of large jitter magnitudes at various jitter frequencies) when jitter is applied to its reference. The applied
jitter magnitude and jitter frequency depends on the applicable standards.
5.4 Jitter Transfer
Jitter transfer or jitter attenuation refers to the magnitude of jitter at the output of a device for a given amount of jitter
at the input of the device. Input jitter is applied at various amplitudes and frequencies, and output jitter is measured
with various filters depending on the applicable standards.
For the Zarlink digital PLLs two internal elements determine the jitter attenuation; the internal low pass loop filter
and the phase slope limiter. The phase slope limiter limits the output phase slope to, for example, 61
μ
s/s.
Therefore, if the input signal exceeds this rate, such as for very large amplitude low frequency input jitter, the
maximum output phase slope will be limited (i.e., attenuated).
Since intrinsic jitter is always present, jitter attenuation will appear to be lower for small input jitter signals than for
large ones. Consequently, accurate jitter transfer function measurements are usually made with large input jitter
signals (for example 75% of the specified maximum tolerable input jitter).
REF1
REF0
REF_SEL
LOCK
Lock Time
Note: LOCK pin behaviour depends on phase and frequency offset of REF1.
相關PDF資料
PDF描述
ZL30101 T1/E1 Stratum 3 System Synchronizer
ZL30101QDC T1/E1 Stratum 3 System Synchronizer
ZL30102QDG1 T1/E1 Stratum 4/4E Redundant System Clock Synchronizer for DS1/E1 and H.110
ZL30102 T1/E1 Stratum 4/4E Redundant System Clock Synchronizer for DS1/E1 and H.110
ZL30102QDG T1/E1 Stratum 4/4E Redundant System Clock Synchronizer for DS1/E1 and H.110
相關代理商/技術參數
參數描述
ZL30102 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1 Stratum 4/4E Redundant System Clock Synchronizer for DS1/E1 and H.110
ZL30102_05 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1 Stratum 4/4E Redundant System Clock Synchronizer for DS1/E1 and H.110
ZL30102QDG 制造商:Zarlink Semiconductor Inc 功能描述:PLL CLOCK SYNTHESIZER SGL 64TQFP - Trays
ZL30102QDG1 制造商:Microsemi Corporation 功能描述:PB FREE T1/E1 SYSTEM SYNCHRONIZER - Trays 制造商:Zarlink Semiconductor Inc 功能描述:PB FREE T1/E1 SYSTEM SYNCHRONIZER - Trays
ZL30105 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/SDH Stratum 3 Redundant System Clock Synchonizer for AdvancedTCA and H.110