參數資料
型號: XRT83SL34IV
廠商: EXAR CORP
元件分類: 數字傳輸電路
英文描述: QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
中文描述: DATACOM, PCM TRANSCEIVER, PQFP128
封裝: 14 X 20 MM, 1.40 MM HEIGHT, TQFP-128
文件頁數: 39/80頁
文件大小: 1154K
代理商: XRT83SL34IV
XRT83SL34
QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
REV. 1.0.0
41
MICROPROCESSOR PARALLEL INTERFACE
XRT83SL34 is equipped with a microprocessor interface for easy device configuration. The parallel port of the
XRT83SL34 is compatible with both Intel and Motorola address and data buses. The XRT83SL34 has an 8-bit
address A[7:0] input and 8-bit bi-directional data bus D[7:0]. The signals required for a generic microprocessor
to access the internal registers are described in Table 16.
TABLE 16: MICROPROCESSOR INTERFACE SIGNAL DESCRIPTION
D[7:0]
Data Input (Output): 8 bits bi-directional Read/Write data bus for register access.
A[7:0]
Address Input: 8 bit address to select internal register location.
PTS1
PTS2
Microprocessor Type Select:
PCLK
Microprocessor Clock Input: Input clock for synchronous microprocessor operation. Maximum
clock speed is 54MHz. This pin is internally pulled “Low” for asynchronous microprocessor operation
when no clock is present.
ALE_AS
Address Latch Input (Address Strobe):
-Intel bus timing, the address inputs are latched into the internal register on the falling edge of ALE.
-Motorola bus timing, the address inputs are latched into the internal register on the falling edge of
AS.
CS
Chip Select Input: This signal must be “Low” in order to access the parallel port.
RD_DS
Read Input (Data Strobe):
-Intel bus timing, a “Low” pulse on RD selects a read operation when CS pin is “Low”.
-Motorola bus timing, a “Low” pulse on DS indicates a read or write operation when CS pin is “Low”.
WR_R/W
Write Input (Read/Write):
-Intel bus timing, a “Low” pulse on WR selects a write operation when CS pin is “Low”.
-Motorola bus timing, a “High” pulse on R/W selects a read operation and a “Low” pulse on R/W
selects a write operation when CS pin is “Low”.
RDY_DTACK
Ready Output (Data Transfer Acknowledge Output):
-Intel bus timing, RDY is asserted “High” to indicate the XRT83SL34 has completed a read or write
operation.
-Motorola bus timing, DTACK is asserted “Low” to indicate the XRT83SL34 has completed a read or
write operation.
INT
Interrupt Output: This pin is asserted “Low” to indicate an interrupt caused by an alarm condition in
the device status registers. The activation of this pin can be blocked by setting the GIE bit to “0” in the
Command Control register.
PTS2
PTS1
0
1
0
P Type
68H C 11, 8051, 80C 188 (a syn c.)
M o to ro la 6 8 K (a syn c.)
In te l x8 6 (syn c.)
In te l i960, M o to ro la 860 (syn c.)
1
相關PDF資料
PDF描述
XRT83SL34 QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XS2F-A422-90-A 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET
XS2F-A422-A90-A 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET
XS2F-A422-AB0-A 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET
XS2F-A422-AC0-A 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET
相關代理商/技術參數
參數描述
XRT83SL34IV-F 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT83SL38 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83SL38_07 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER
XRT83SL38ES 功能描述:外圍驅動器與原件 - PCI 8 CHT1/E1LIUSH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT83SL38ES-BG 功能描述:界面開發工具 Eval System for XRT83SL38 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V