- 您現在的位置：買賣IC網 > PDF目錄206198 > XRT83SL34IV (EXAR CORP) QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR PDF資料下載
參數資料
| 型號： | XRT83SL34IV |
| 廠商： | EXAR CORP |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| 中文描述： | DATACOM, PCM TRANSCEIVER, PQFP128 |
| 封裝： | 14 X 20 MM, 1.40 MM HEIGHT, TQFP-128 |
| 文件頁數： | 18/80頁 |
| 文件大小： | 1154K |
| 代理商： | XRT83SL34IV |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
XRT83SL34
QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
REV. 1.0.0
22
JITTER ATTENUATOR
To reduce phase and frequency jitter in the recovered clock, the jitter attenuator can be placed in the receive
signal path. The jitter attenuator uses a data FIFO (First In First Out) with a programmable depth that can vary
between 2x32 and 2x64. The jitter attenuator can also be placed in the transmit signal path or disabled
altogether depending upon system requirements. The jitter attenuator, other than using the master clock as
reference, requires no external components. With the jitter attenuator selected, the typical throughput delay
from input to output is 16 bits for 32 bit FIFO size or 32 bits for 64 bit FIFO size. When the read and write
pointers of the FIFO in the jitter attenuator are within two bits of over-flowing or under-flowing, the bandwidth of
the jitter attenuator is widened to track the short term input jitter, thereby avoiding data corruption. When this
situation occurs, the jitter attenuator will not attenuate input jitter until the read/write pointer’s position is outside
the two bits window. Under normal condition, the jitter transfer characteristic meets the narrow bandwidth
requirement as specified in ITU- G.736, ITU- I.431 and AT&T Pub 62411 standards.
In T1 mode the Jitter Attenuator Bandwidth is always set to 3Hz. In E1 mode, the bandwidth can be reduced
through the JABW control signal. When JABW is set “High” the bandwidth of the jitter attenuator is reduced
from 10Hz to 1.5Hz. Under this condition the FIFO length is automatically set to 64 bits and the 32 bits FIFO
length will not be available in this mode. Jitter attenuator controls are available on a per channel basis in the
Host mode and on a global basis in the Hardware mode.
GAPPED CLOCK (JA MUST BE ENABLED IN THE TRANSMIT PATH)
The XRT83SL34 LIU is ideal for multiplexer or mapper applications where the network data crosses multiple
timing domains. As the higher data rates are de-multiplexed down to T1 or E1 data, stuffing bits are removed
which can leave gaps in the incoming data stream. If the jitter attenuator is enabled in the transmit path, the
32-Bit or 64-Bit FIFO is used to smooth the gapped clock into a steady T1 or E1 output. The maximum gap
width of the 8-Channel LIU is shown in Table 2.
NOTE: If the LIU is used in a loop timing system, the jitter attenuator should be enabled in the receive path.
TABLE 2: MAXIMUM GAP WIDTH FOR MULTIPLEXER/MAPPER APPLICATIONS
FIFO DEPTH
MAXIMUM GAP WIDTH
32-Bit
20 UI
64-Bit
50 UI
相關PDF資料 |
PDF描述 |
|---|---|
| XRT83SL34 | QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XS2F-A422-90-A | 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET |
| XS2F-A422-A90-A | 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET |
| XS2F-A422-AB0-A | 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET |
| XS2F-A422-AC0-A | 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83SL34IV-F | 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRT83SL38 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83SL38_07 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER |
| XRT83SL38ES | 功能描述:外圍驅動器與原件 - PCI 8 CHT1/E1LIUSH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83SL38ES-BG | 功能描述:界面開發工具 Eval System for XRT83SL38 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。