XRT74L73
3 CHANNEL, ATM UNI/PPP DS3/E3 FRAMING CONTROLLER
REV. P1.0.1
PRELIMINARY
325
N
OTE
:
This bit is ignored whenever the TxLOS bit-field is
set.
5.2.4.2.1.2
Transmit LOS Enable - Bit 1
This read/write bit field allows the user to transmit an
LOS (Loss of Signal) pattern to the remote terminal,
upon software control. Table 71 relates the contents
of this bit field to the Transmit E3 Framer block’s ac-
tion.
N
OTE
:
When this bit is set, it overrides all of the other bits in
this register.
5.2.4.2.1.3
Transmitting FERF (Far-End
Receive Failure) Indicator or Yellow Alarm
The XRT74L73 Framer IC permits the user to control
the state of the “A” bit-field, within each outbound E3
frame. This can be achieved by writing the appropri-
ate data into the TxASource[1:0] bit-fields within the
Tx E3 Configuration Register, as illustrated below.
The following table presents the relationship between
the contents of TxASource[1:0] and the resulting
source of the “A” bit.
T
ABLE
70: T
HE
R
ELATIONSHIP
BETWEEN
THE
CONTENTS
OF
B
IT
2 (T
X
AIS E
NABLE
)
WITHIN
THE
T
X
E3
C
ONFIGURATION
R
EGISTER
,
AND
THE
RESULTING
T
RANSMIT
E3 F
RAMER
B
LOCK
’
S
A
CTION
B
IT
2
T
RANSMIT
E3 F
RAMER
’
S
A
CTION
0
Normal Operation:
The Transmit Section of the XRT74L73 Framer IC will transmit E3 traffic based upon data that it accepts via
the Transmit Payload Data Input Interface block, the Transmit Overhead Data Input Interface block, the Trans-
mit HDLC Controller block and internally generated overhead bytes.
Transmit AIS Pattern:
The Transmit E3 Framer block will overwrite the E3 traffic, within an Unframed “All Ones” pattern.
1
T
ABLE
71: T
HE
R
ELATIONSHIP
BETWEEN
THE
CONTENTS
OF
B
IT
1 (T
X
LOS)
WITHIN
THE
T
X
E3 C
ONFIGURATION
R
EGISTER
,
AND
THE
RESULTING
T
RANSMIT
E3 F
RAMER
B
LOCK
’
S
A
CTION
B
IT
1
T
RANSMIT
E3 F
RAMER
’
S
A
CTION
0
Normal Operation:
The Overhead bits are either internally generated, or they are inserted via the Transmit Overhead Data Input
Interface or the Transmit HDLC Controller blocks. The Payload bits are received from the Transmit Payload
Data Input Interface.
Transmit LOS Pattern:
When this command is invoked the Transmit E3 Framer will do the following.
Set all of the overhead bytes to "0" (including the FA1 and FA2 bytes)
Overwrite the E3 payload bits with an "all zeros" pattern.
1
TXE3 CONFIGURATION REGISTER (ADDRESS = 0X30)
B
IT
7
B
IT
6
B
IT
5
B
IT
4
B
IT
3
B
IT
2
B
IT
1
B
IT
0
Tx
BIP-4
Enable
TxASourceSel[1:0]
TxNSourceSel[1:0]
Tx AIS
Enable
Tx LOS
Enable
Tx FAS
Source
Select
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
X
X
0
0
0
0
0