參數資料
型號： XRT7302
廠商： Exar Corporation
英文描述： 2 Channel E3/DS3/STS-1 Line Interface Unit(2通道 E3/DS3/STS-1線接口單元)
中文描述： 2頻道E3/DS3/STS-1線路接口單元（2通道E3/DS3/STS-1線接口單元）
文件頁數： 55/62頁
文件大?。?/td> 715K
代理商： XRT7302
á
PRELIMINARY
2 CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT7302
REV. P1.1.6
51
set to "1" if the Clock Recovery PLL is out of lock with
the incoming line signal.
Bit D3 - RLOS(n) (Receive Loss of Signal Status -
Channel(n))
This Read-Only bit-field indicates whether or not
Channel(n) of the Receiver is currently declaring an
LOS (Loss of Signal) Condition.
This bit-field is set to "0" if Channel(n) is NOT current-
ly declaring the LOS Condition or, this bit-field is set
to "1" if Channel(n) is declaring an LOS Condition.
Bit D2 - ALOS(n) (Analog Loss of Signal Status -
Channel(n))
This Read-Only bit-field indicates whether or not the
Channel(n) Analog LOS Detector is currently declar-
ing an LOS condition.
This bit-field is set to "0" if the Analog LOS Detector is
NOT currently declaring an LOS condition. This bit-
field is set to "1" if the Analog LOS Detector is cur-
rently declaring an LOS condition.
N
OTE
:
The purpose is to isolate the Detector (e.g., either
the Analog LOS or the Digital LOS detector) that is declar-
ing the LOS condition. This feature may be useful for trou-
bleshooting/debugging purposes.
Bit D1 - DLOS(n) (Digital Loss of Signal Status -
Channel(n))
This Read-Only bit-field indicates whether or not the
Channel(n) Digital LOS Detector is currently declar-
ing an LOS condition.
This bit-field is set to "0" if the Digital LOS Detector is
NOT currently declaring an LOS condition. This bit-
field is set to "1" if the Digital LOS Detector is current-
ly declaring an LOS condition.
N
OTE
:
The purpose is to isolate the Detector (e.g., either
the Analog LOS or the Digital LOS detector) that is declar-
ing the LOS condition. This feature may be useful for trou-
bleshooting/debugging purposes.
Bit D0 - DMO(n) (Drive Monitor Output Status -
Channel(n))
This Read-Only bit-field reflects the status of the
DMO output pin.
5.2.2
Command Register CR1
The bit-format and default values for Command Reg-
ister CR1-(n) are listed below followed by the function
of these bit-fields.
COMMAND REGISTER CR1-(N)
Bit D4 - TxOFF(n) (Transmitter OFF - Channel(n))
This Read/Write bit-field is used to turn off the Chan-
nel(n) Transmitter.
Writing a "1" to this bit field turns off the Transmitter
and tri-state the Transmit Output. Writing a "0" to this
bit-field turns on the Transmitter.
Bit D3 - TAOS(n) (Transmit All OneS - Channel(n))
This Read/Write bit-field is used to command the
Channel(n) Transmitter to generate and transmit an
all “1’s” pattern onto the line.
Writing a "1" to this bit-field commands the Transmit-
ter to transmit an all “1’s” pattern onto the line. Writ-
ing a "0" to this bit-field commands normal operation.
Bit D2 - TxClkINV(n) (Transmit Clock Invert -
Channel(n))
This Read/Write bit-field is used to configure the
Transmitter in the XRT7302 to sample the signal at
the TPData and TNData pins on the rising edge or
falling edge of TxClk (the Transmit Line Clock signal).
Writing a "1" to this bit-field configures the Transmitter
to sample the TPData and TNData input pins on the
rising edge of TxClk. Writing a "0" to this bit-field con-
figures the Transmitter to sample the TPData and
TNData input pins on the falling edge of TxClk.
Bit D1 - TxLEV(n) (Transmit Line Build-Out En-
able/Disable Select - Channel(n))
This Read/Write bit-field is used to enable or disable
the Channel(n) Transmit Line Build-Out circuit in the
XRT7302.
Setting this bit-field "High” disables the Channel(n)
Line Build-Out circuit. In this mode, Channel(n) out-
puts partially-shaped pulses onto the line via the
TTIP(n) and TRing(n) output pins.
Setting this bit-field "Low" enables the Channel(n)
Line Build-Out circuit. In this mode, Channel(n) out-
puts shaped pulses onto the line via the TTIP(n) and
TRing(n) output pins.
In order to comply with the Isolated DSX-3/STSX-1
Pulse Template Requirements (per Bellcore GR-499-
CORE or GR-253-CORE):
a. Set this bit-field to "1" if the cable length between
the Cross-Connect and the transmit output of Chan-
nel(n) is greater than 225 feet.
b. Set this bit-field to "0" if the cable length between
the Cross-Connect and the transmit output of Chan-
nel(n) is less than 225 feet.
N
OTE
:
This bit-field is active only if the XRT7302 is config-
ured to operate in the DS3 or SONET STS-1 Modes.
D4
D3
D2
D1
D0
TxOFF(n) TAOS(n)
TxClkINV(n)
TxLEV(n) TxBIN(n)
0
0
0
0
0
相關PDF資料
PDF描述
XRT73L02M TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73L02MIV TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73L02 2 Channel E3/DS3/STS-1 Line Interface Unit(2通道 E3/DS3/STS-1線接口單元)
XRT73L03A 3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
XRT73L03AIV 3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
相關代理商/技術參數
參數描述
XRT7302IV 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM Transceiver
XRT73L00 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73L00A 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73L00AES 功能描述:界面開發工具 Eval System for XRT73L00A Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XRT73L00AIV 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*