- 您現在的位置：買賣IC網 > PDF目錄376460 > XRT71D04 (Exar Corporation) 4-Channel E3/DS3/STS-1 Jitter Attenuator,STS-1 to DS3 Desynchronizer(達到E3/DS3/STS-1振蕩要求的4通道振蕩衰減器) PDF資料下載
參數資料
| 型號： | XRT71D04 |
| 廠商： | Exar Corporation |
| 英文描述： | 4-Channel E3/DS3/STS-1 Jitter Attenuator,STS-1 to DS3 Desynchronizer(達到E3/DS3/STS-1振蕩要求的4通道振蕩衰減器) |
| 中文描述： | 4通道E3/DS3/STS-1抖動衰減器，STS - 1的到DS3 Desynchronizer（達到E3/DS3/STS-1振蕩要求的4通道振蕩衰減器） |
| 文件頁數： | 4/21頁 |
| 文件大?。?/td> | 223K |
| 代理商： | XRT71D04 |
XRT71D04
4 CHANNEL E3/DS3/STS-1 JITTER ATTENUATOR, STS-1 TO DS3 DESYNCHRONIZER
REV. P1.0.2
á
PRELIMINARY
3
PIN DESCRIPTIONS
PIN DESCRIPTION
P
IN
#
N
AME
T
YPE
D
ESCRIPTION
1
AVDD
****
Analog Power Supply = 5V±5% or 3.3V±5%
2
NC
3
VSS
****
Digital Ground
4
RRCLK0
O
Received Recovered Output (De-jittered) Clock - channel 0:
Output is the de-jittered or smoothed clock if the jitter attenuator is enabled.
The de-jittered data, RRPOS/RRNEG are clocked to this signal.
If RRCLKES is “l(fā)ow”, RRPOS/RRNEG will be updated at the falling edge of
RRCLK.
If RRCLKES is “high”, RRPOS/RRNEG will be updated at the rising edge of
RRCLK.
5
RRPOS0
O
Received Recovered Positive Data (De-Jittered) Output - channel
0:
De-jittered positive data output. Updated on the rising or falling edge of
RRCLK, depending upon the state of the RRCLKES input pin (or bit-field set-
ting).
6
RRNEG0
O
Received Recovered Negative Data (De-Jittered) Output - channel
0:
De-jittered negative data output. Updated on the rising or falling edge of
RRCLK, depending upon the state of the RRCLKES input pin (or bit-field set-
ting).
7
RRCLKES
I
Received Recovered Clock Edge Select Input:
Hardware Mode:
1. When RRCLKES = “0”, then RRPOS and RRNEG are updated on the fall-
ing edge of RRCLK
2. When RRCLKES = “1”, then RRPOS and RRNEG are updated on the rising
edge of RRCLK
N
OTE
:
This applies to all channels.
Host Mode
Connect this pin to GND when the 71D04 is configured in the Host Mode.
Internal 50 K Ohm pull-down resistor.
8
NC
9
RST
I
Reset Input.
(Active-Low):
A high-low transition will re-center the internal FIFO, and will clear the Com-
mand Registers (for Host Mode operation). Resetting this pin may corrupt data
within the device.
For normal operation, pull this pin to VDD.
Internal 50 K Ohm pull-up resistor.
10
DS3/E3_ch1
I
DS3/E3 Select Input - channel 1
:
This pin along with the STS-1 mode select pin selects the operating mode. The
following table provides the configuration:
STS-1
DS3/E3
XRT71D04 Operating Mode
0 0 DS3 (44.736 MHz)
0 1 E3 (34.368 MHz)
1 0 STS-1 (51.84 MHz)
1 1 E3 (34.368 MHz)
Internal 50 K Ohm pull-down resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| XRT7234 | E3 ATM User Network Interface(E3異步傳輸模式用戶網絡接口) |
| XRT7245 | DS3 ATM User Network Interface(DS3異步傳輸模式用戶網絡接口) |
| XRT7288IP | CEPT1 Line Interface |
| XRT7288 | CEPT1 Line Interface(CEPT1線接口) |
| XRT7288IW | CEPT1 Line Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT71D04ES | 功能描述:時鐘合成器/抖動清除器 4CH T3/E3 JA w/T73LC04A RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRT71D04IV | 功能描述:時鐘合成器/抖動清除器 4CH E3/DS3/STS1 JIT ATTEN DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRT71D04IVTR | 功能描述:時鐘合成器/抖動清除器 4CH E3/DS3/STS1 JIT ATTEN DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRT7250 | 制造商:EXAR 制造商全稱:EXAR 功能描述:DS3/E3 FRAMER IC |
| XRT7250ES-PCI | 功能描述:界面開發工具 Evaluation Board for XRT7250 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。